Results 1 to 7 of 7

Thread: Discovery 2 Ride Height?

  1. 12th September 2009, 02:26 PM #1
    Shaker Guest

    Discovery 2 Ride Height?

    Has anybody got the the standard ride height measurements for Disco 2 TD5?

    I read it here a while back, but can't find it by searching.
    Reply With Quote Reply With Quote
  2. 12th September 2009, 06:37 PM #2
    Baffle's Avatar
    Baffle
    Baffle is offline Master
    Join Date
    Dec 2007
    Location
    Tamborine Mountain
    Posts
    512
    Total Downloaded
    0
    Mate all I know is 700mm from the bottom of the (16")rim to bottom of guard, this is standard on the air bag rear end, hope it helps
    Reply With Quote Reply With Quote
  3. 12th September 2009, 07:02 PM #3
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,035
    Total Downloaded
    0
    Hub centre to bottom edge of guard
    ...front 500mm +/- 15mm
    ...rear SLS 473mm +/- 15mm ...rear coils 485mm +/- 15mm.

    It seamed that for most the front was around 485mm when new.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  4. 12th September 2009, 07:17 PM #4
    bluerazor's Avatar
    bluerazor
    bluerazor is offline Fossicker
    Join Date
    May 2009
    Posts
    53
    Total Downloaded
    0
    I've read in the Rave manual and it states 61.5 from the tip of bumber stops to axle base
    On mine i used a steel block of 60X60mm then with the Nanocom i lowered the rear till it sat on the blocks and stored the values
    Works fine for me
    Cheers
    Vince
    Reply With Quote Reply With Quote
  5. 13th September 2009, 08:14 AM #5
    Shaker Guest
    Sorry, I should have mentioned that is coil sprung, & the measurements that I can't find were from the bottom of the rim to the underside of the guard.
    Reply With Quote Reply With Quote
  6. 13th September 2009, 08:30 AM #6
    smally4.6's Avatar
    smally4.6
    smally4.6 is offline Master
    Join Date
    Jul 2007
    Location
    Hobart Tassie
    Posts
    167
    Total Downloaded
    0
    Hi Shaker
    i measured before & after lifting mine...
    Measurement are from centre of rim/hub to bottom of flare/guard...
    before lift front was 487mm rear was 485mm..
    after fitting lifted coils ... front was 560mm & rear 535mm
    cheers smally
    Reply With Quote Reply With Quote
  7. 13th September 2009, 12:28 PM #7
    scarry's Avatar
    scarry
    scarry is offline Swaggie
    Join Date
    Apr 2008
    Location
    Brisbane,some of the time.
    Posts
    13,888
    Total Downloaded
    0
    My coiler is 485mm rear & 508mm front,both taken from centre of rim to edge of guard.

    Has set of King standards,which are a bit soft on the rear.
    Reply With Quote Reply With Quote
« d2a intercooler into d2 | Suggested alternates to cargo barrier? »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!