I thought it was pretty lightweight stuff. I agree with all said so far, I'm now wondering, like Steve, about whether the Whiworths stuff is any better.
What I did on my Tray Landie was to use Flashtac from Bunnings on the inside of the firewall & the transmission hump. Works really well.
Selleys I think make it.
P.S. Sorry about sending the thread off on soundproofing

__________________
DeeJay
1985 110 Extra Cab w/tray.350 Chev.
1985 Isuzu S/Wagon - Blue
1996 Disco Mums Taxi

Tonight I installed the PAS pump after redoing the seal etc.
Being a Stage1 engine, it never had a PAS pump fitted originally - it just had a blanking plate on the front cover.

When it wouldn't go into the cover easily I thought it was just hanging up on the o-ring, but after trying to pull it in gently with the mounting bolts without success I knew something was wrong. A closer look revealed this:



The bolt was installed from inside the front cover but should have been like this one that Isuzubob posted in his seal tutorial:


Strangely, the two parts that the bolt goes through are both threaded...
I removed it and re-fitted from the back of the cover and all is well.



It will get a decent clean before I paint it, but figured it was better to do it after the pump was fitted so the dirt didn't get into the bearing/seal etc.
Steve

Not much really to show for a few nights of cutting/welding/grinding and setting myself alight.

I've made the 2 engine mounts to go on the chassis, and also the LH mount to go on the engine itself (I already had the RH one).

While I was at it, I cut a hole in the back of the one to go on the engine so that I can get a socket onto the nut of the rubber mount . Figure I'll fit the rubber mount on the bench so I can tighten the nut properly, and then bolt them onto to the engine.




Steve

good to see you've moved the production into the kitchen

__________________
Damien
------------------------------------------------

Not production, just the documentation department
For some reason camera's don't like mig spatter and grinder dust...

I did get the "what are they, and why are they on my table" look when SWMBO went to sit down to breakfast this morning......they're back in the shed now....

Steve

VERY slow progress over the last month due to work commitments.

Started getting back into it this week, and finally got the clutch pivot modification/repair completed. I welded the shank of a bolt to the pivot and drilled the existing hole in the bell housing all the way through, then put a nut on the bolt to hold it all together.

Here's the pivot and bolt ready to be welded together:



And the finished job. Also had to grind a bit of a flat section for the nut to sit on:



Getting the bell housing off resulted in the front plate of the gearbox separating from the rest of the box, and I found a few problems when I removed the plate to replace the gasket.
I'll leave them in their separate thread:http://www.aulro.com/afvb/technical-...-problems.html


Steve

Came to a halt for now with the gearbox waiting for parts etc, so decided to make a start on a few engine jobs:
- Check the clutch condition
- Check the rear crank seal to see if its leaking
- Replace the winged sump with a truck one to make running the dump pipe from the turbo easier.

Here's a couple of photos of the rear seal area. There's a bit of oil film around, but I'm pretty sure its not coming from the seal.
I'm thinking its been blown back from the leaking sump gasket.
The crank itself seems basically dry, and there is no oil slung out on the forward face of the flywheel (just some accumulated clutch dust).





I'm just going to fit the truck sump with a new gasket and leave it at that unless someone can see something I've missed.

Steve

Steve, Replace the rear crank seal. It's not worth the risk. You can bet your bottom dollar that it will leak after you have put it all back together. It is an easy job to do now but if you have to do it later after it's all back in the vehicle???????. Get my drift.

__________________
Cheers......Brian
1986 110 4BD1 Turbo Isuzu County Dualcab
1985 110 V8 County (soon to be Isuzued)
Ex RAAF No.5 trailer ARN 232-501
Haulmark 1 ton trailer

Yes - I know what you mean
Just trying to balance "might as well do it while its easy" with "if it ain't broke...."

Is there any benefit in using the flash 2 part seal if the crank is OK?

Steve

Hi steve I've been looking through a parts book for a perentie and it shows a breather in the bell housing,it just a piece of 4.8mm bundy tube with a lenght of hose on it.It might be a good thing to do while is easy to get at.