Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20

Thread: My new 101

  1. #11
    Join Date
    Jan 1970
    Location
    Perth. SOR
    Posts
    180
    Total Downloaded
    0

    plates

    Even these 2 aussie plates have different numbers 501/502 and the GS is missing on one.
    Attached Images Attached Images

  2. #12
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,474
    Total Downloaded
    0
    Quote Originally Posted by DODGE View Post
    Even these 2 aussie plates have different numbers 501/502 and the GS is missing on one.
    The 5.02 is the "model number" - REMLR has the model numbers as 5.02 for the first half of ARNs and 5.2 for the later ones but I think that may have been a typo and they should all be 5.02.

    What 101 is that, that has the Rapier Plate that has 5.01 on it?

    I cannot answer your questions on this as like all things military there are inconsistencies everywhere.

    I assume you are familiar with the 101 ARN page on REMLR http://www.remlr.com/ARN/ARNs_101.php

    So is the 101 you have now 12v or still 24v?

    Garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon

  3. #13
    Join Date
    Jan 2008
    Location
    Nowra NSW
    Posts
    3,906
    Total Downloaded
    0
    Quote Originally Posted by DODGE View Post
    12v coil that has 24v running to it. winch mount that has seen a bit of work. front bump stops that have also seen some work. door top markings.
    24 volt military suppressed ignition systems use 12 volts at the coil regardless of the vehicle battery voltage.

  4. #14
    Join Date
    Jan 1970
    Location
    Perth. SOR
    Posts
    180
    Total Downloaded
    0

    plates / coil

    The rapier plate with 501 is from the remlr site under data plates. mine has the step down box which i have now removed to check as it wasnt hooked up to anything.it has 24v going straight to the 12v coil. mine is still 24v just with a small bosch 24v alt. Gaz

  5. #15
    Join Date
    Jan 1970
    Location
    Perth. SOR
    Posts
    180
    Total Downloaded
    0

    BAC plates

    Would be good to get a few more data plate pictures on the site and matched to the arns/ owners. Gaz

  6. #16
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,474
    Total Downloaded
    0
    Quote Originally Posted by 101RRS View Post
    I assume you are familiar with the 101 ARN page on REMLR http://www.remlr.com/ARN/ARNs_101.php
    Quote Originally Posted by DODGE View Post
    The rapier plate with 501 is from the remlr site under data plates.
    That interesting as none of the model numbers in the link above are 5.01 - except if the pic is from one of the two trial vehicles - top two in the link are the trials vehicles - top one is owned by Iain Reed and second one is Anthony Johnson - I expect the pic is AJs trial vehicle so has model number 5.01.

    A shame Iain is not on the forum these days as he could clarify.

    How is that for deduction .

    Garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon

  7. #17
    Join Date
    Jan 1970
    Location
    Perth. SOR
    Posts
    180
    Total Downloaded
    0

    todays progress

    Fitted a new clutch hose so i could drive the old girl off the trailer. unlocked the hubs and no drive, front shaft turning so i guess its not modded to part time after all. so the free wheeling hubs look pretty but will prob come off. started to clean up some wiring and will start removing the gas setup tomorrow. Gaz

  8. #18
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,474
    Total Downloaded
    0
    Quote Originally Posted by DODGE View Post
    Drove the old girl off the trailer. unlocked the hubs and no drive, front shaft turning so i guess its not modded to part time after all. so the free wheeling hubs look pretty but will prob come off. started to clean up some wiring and will start removing the gas setup tomorrow. Gaz
    Did you try locking and unlocking the CDL and see what happens. If it was actually modded for part time how do you engage 4wd? There should be a lever like other series LRs in the cabin

    I suspect all they have done is just replaced the front hubs with what you have - so you will have to drive with the cdl in and the front hubs unlocked - then when offroad lock the front hubs and drive it like any other 101 with the cdl in or out as required.

    I would take the gas off mine as well, but here in the ACT the vehicle has to go the the Government inspection station to have the gas removal engineered. There is no way I want a 101 near a Government inspection station.

    Garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon

  9. #19
    Join Date
    Jan 1970
    Location
    Perth. SOR
    Posts
    180
    Total Downloaded
    0

    cdl

    If it was part time you would just operate the cdl on and off for it it to be 2wd /4wd. at the moment one of the hoses to the cdl is missing so thats another job to add to the list. i liked the handling of my old one with constant 4x4 so will set it up as it should be for now. less dramas for rego inspection.If the gas system was plated and modern i would probably keep it but its ancient and the tanks are way to big. to get it tested/inspected etc would be more drama than its worth. I just want it to be stock and basic to get it passed inspection then i can add the gear i want onto it later. Gaz

  10. #20
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,474
    Total Downloaded
    0
    Quote Originally Posted by DODGE View Post
    Drove the old girl off the trailer. unlocked the hubs and no drive, front shaft turning so i guess its not modded to part time after all. so the free wheeling hubs look pretty but will prob come off. started to clean up some wiring and will start removing the gas setup tomorrow. Gaz
    Did you try locking and unlocking the CDL and see what happens. If it was actually modded for part time how do you engage 4wd? There should be a lever like other series LRs in the cabin

    I suspect all they have done is just replaced the front hubs with what you have - so you will have to drive with the cdl in and the front hubs unlocked - then when offroad lock the front hubs and drive it like any other 101 with the cdl in or out as required.

    I would take the gas off mine as well, but here in the ACT the vehicle has to go the the Government inspection station to have the gas removal engineered. There is no way I want a 101 near a Government inspection station.

    To answer your other question
    The 4 litre tin of Protec paint
    IMG_20200126_222400.jpg

    And the spraycan
    IMG_20200126_222510.jpg

    4 litres (is cheap) is more than enough to do a 101 and probably the inside as well. Spraycans are great for all the touchups etc.

    Garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon

Page 2 of 2 FirstFirst 12

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!