Wipers and Ignition+Key

[11laura]

Hello all,

I have a Series 1 1957 coming, and I need a full wiper motor, blade and connections, plus a new ignition and key. Alternatively could someone point me in the direction of having a key cut for the existing ignition.
Many thanks for you help in advance.

Cheers

Reg

[1950landy]

Hello all,

I have a Series 1 1957 coming, and I need a full wiper motor, blade and connections, plus a new ignition and key. Alternatively could someone point me in the direction of having a key cut for the existing ignition.
Many thanks for you help in advance.

Cheers

Reg
If you just take the ignition switch to a lock smith ( not one in a shopping centre ) & they will be able to remove the barrel & make new keys or even change the barrel to suit another key of the same type. I had all the locks on my MGBGT changed to be lock alike so I had the one key to fit the ignition , doors , hatch & glovebox, it wasn't that expensive. There is a number stamped into the face of barrel in the old days you could just quote that number & buy a new key or tell the lock smith the number & he would cut it for you. Not sure if they can still do that though.

[5380]

Hello all,<br>
<br>
I have a Series 1 1957 coming, and I need a full wiper motor, blade and connections, plus a new ignition and key. Alternatively could someone point me in the direction of having a key cut for the existing ignition.<br>
Many thanks for you help in advance.<br>
<br>
Cheers<br>
<br>
Reg <br><br>I might have one in the container to suit your '57. Hopefully, I'll get a chance soon to brave the heat and smoke and have a look for you. If I haven't got a '57 dated one, I should have something close. You will have to pull it apart and clean out the dried up zinc ? based grease. Make sure you take note of the positioning and timing of the gear set!<br>Good luck with your project! 5380<br>
<br>

[JDNSW]

If the number is stamped on the barrel, any qualified locksmith should be able to cut a key. I have done this (not for a Landrover) within the last few years.

[Bundy]

maybe someone like this for the key
TRIUMPH KEY - WILMOT BREEDEN KEYS - KEYS CUT TO CODE FA/ MRN /FP/ FS - - | eBay (https://www.ebay.com.au/itm/TRIUMPH-KEY-WILMOT-BREEDEN-KEYS-KEYS-CUT-TO-CODE-FA-MRN-FP-FS/173647073865?hash=item286e2c1249:g:h-4AAOSwalBddIwg&frcectupt=true)

Wiper motors do come up at swap meets, Gumtree and eBay

This is what you are looking for

Land Rover wiper motor series 1/2/2A, mini moke lucas fw2 reconditioned | eBay (https://www.ebay.co.uk/itm/Land-Rover-wiper-motor-series-1-2-2A-mini-moke-lucas-fw2-reconditioned/264299501414?hash=item3d897a5766:g:4L0AAOSwUP5cTa0 R)

Stainless Steel Wiper Arm Eye Peg Fitting Land Rover Series 1 80 86 88 107 | eBay (https://www.ebay.com.au/itm/Stainless-Steel-Wiper-Arm-Eye-Peg-Fitting-Land-Rover-Series-1-80-86-88-107/282799343346?epid=2103974451&hash=item41d82786f2:g:alUAAOSwVA5aO9L~)

[11laura]

If you just take the ignition switch to a lock smith ( not one in a shopping centre ) & they will be able to remove the barrel & make new keys or even change the barrel to suit another key of the same type. I had all the locks on my MGBGT changed to be lock alike so I had the one key to fit the ignition , doors , hatch & glovebox, it wasn't that expensive. There is a number stamped into the face of barrel in the old days you could just quote that number & buy a new key or tell the lock smith the number & he would cut it for you. Not sure if they can still do that though.


Thank you