Gillie
19th March 2020, 10:11 PM
After the wifes Range Rover 3.6 TDV8 Luxury Vogue 2008 model started leaking oil a bit of investigation revealed it to be the RHS Turbo. The common way to fix this is to drop the chassis from the Body if it were a sports but this cannot be done with a vogue. Instead the common way appears to be to be to drop the motor. With quotes of around $5,500 being the norm I thought I would have a go armed with RAVE and a plentiful tool box. With not much info out there I can say that it is possible to replace the turbo on the car but 10/10 for difficulty and I would not recommend. It was like performing key hole surgery and bolts in impossible to get to places really had me thinking.
The hoist basically paid for itself and made this job alot easier.
158803
I don't know why this picture appears to be sideways?
Disconnect the battery and remove the front RHS tyre.
158804
Remove the inner guard and there is also an inspection guard behind that behind the shocky. This guard could not be removed completely and hung down with maybe the brake line going through it from memory.
158805
From here you can remove the bash plate, catalytic converter, heat shield, Starter motor, another heat shield and unbolt the heat shield above the turbo but you can't get this one out until the turbo is removed. but is necessary to be able to get to the bolts on the manifold on top of the turbo.
158806
You can remove the inlet and outlet clean air side hoses and mounting brackets for the turbo. There is a breather pipe that needs to be unbolted so you can move it to get access to some of these bolts on the heat shield. The breather pipe and heat shield above the turbo is accessed through the small inspection hole from the inner guard. The three bolts on the top of the turbo were the most difficult bit to get undone and I ended up having to purchase a 3/8ths socket set to add to the 1/2 inch and 1/4 inch sets. The oil return seems to be a common issue but this one was clean as clean.
158807
With the turbo out, closer inspection revealed some play in the shaft which at 300,000 RPM is not what you want.
158808
To fit the new turbo was fairly easy with the most difficult part being that breather pipe. I also replaced the inter cooler hoses to turbo intake.
158809
I don't know why this picture appears to be sideways?
Don't forget the gaskets!!! and pre-lube the new turbo. An oil change and a fresh air cleaner I also ran a turbo cleaner through the fuel tank and 2,000 km later there are no sign of oil leaks. With Parts and a cracking new socket set I was in it for around $2,050 so not a bad saving. Hope this helps someone as I could find not much out there when I was researching this one.
The hoist basically paid for itself and made this job alot easier.
158803
I don't know why this picture appears to be sideways?
Disconnect the battery and remove the front RHS tyre.
158804
Remove the inner guard and there is also an inspection guard behind that behind the shocky. This guard could not be removed completely and hung down with maybe the brake line going through it from memory.
158805
From here you can remove the bash plate, catalytic converter, heat shield, Starter motor, another heat shield and unbolt the heat shield above the turbo but you can't get this one out until the turbo is removed. but is necessary to be able to get to the bolts on the manifold on top of the turbo.
158806
You can remove the inlet and outlet clean air side hoses and mounting brackets for the turbo. There is a breather pipe that needs to be unbolted so you can move it to get access to some of these bolts on the heat shield. The breather pipe and heat shield above the turbo is accessed through the small inspection hole from the inner guard. The three bolts on the top of the turbo were the most difficult bit to get undone and I ended up having to purchase a 3/8ths socket set to add to the 1/2 inch and 1/4 inch sets. The oil return seems to be a common issue but this one was clean as clean.
158807
With the turbo out, closer inspection revealed some play in the shaft which at 300,000 RPM is not what you want.
158808
To fit the new turbo was fairly easy with the most difficult part being that breather pipe. I also replaced the inter cooler hoses to turbo intake.
158809
I don't know why this picture appears to be sideways?
Don't forget the gaskets!!! and pre-lube the new turbo. An oil change and a fresh air cleaner I also ran a turbo cleaner through the fuel tank and 2,000 km later there are no sign of oil leaks. With Parts and a cracking new socket set I was in it for around $2,050 so not a bad saving. Hope this helps someone as I could find not much out there when I was researching this one.