Garage roof storage Brains trust question

[NavyDiver]

Looking for a movable attic, storage for boxes, ladder, bikes and that important stuff I don't wish to throw away.

A place in QLD will do it for you Install and fit it.
Lost the link sorry!


A place in the USA has it- PRICY plus. E-Z Lift Retractable Garage Storage Rack - MADE IN USA (https://ezgaragelift.com/)


https://www.youtube.com/watch?v=xn-bvpqFTdM&msockid=5693607789f111f0949daec0f5d92c99

Looking for a smart way for DYI as I am tight [bigrolf]

[Blknight.aus]

you need.. (and theres lots of bits missed as this is just an outline. little things like, before you drill your holes go up into the roof and work out where the trusses are so you can drill adjacent to the beam.

a metal bed frame
4x pullies
4x eyebolts long enough to pass through your ceiling panels
4x braces to span your roof trusses
a length 20mm metal tube longer than the bedframe is wide
a length of rod (about 6mm(
mount bearings for the rod.
a drill and suitable bit
some eye or hook bolts to act as guides for the rope (pullies work better but Im tight was a key descriptior)
some good rope

with the bed frame supported in 4 spots on the long side at your desired at rest height

attach the mount bearings to the length of tube and attach that across the center of te bed on the underside
attach the 4 pullies to the side of the frame positioned so the rope can pass from the rod on the under side of the bed and exit straight upwards
drill 4 holes in the rod inside the bed frame 2 each side, near the frame
cut your rope into 4 lengths long enough to go from the tube in the middle of the frame to the corner and up to the roof +1m
position your guide hooks and thread the rope through the pullies and the guides and attach one rope per corner to the nearest corresponding hole in the bed frame.
mark and drill 4 holes in the roof that line up with the corners of the bedframe where the rope will attach.
climb up in the roof and secure above the base of the truss a brace that bridges 2 trusses and passes over the hole. one per hole
screw your eyebolts in through the holes and the brace.
tie the ropes to the corresponding eyebolt
adjust the lines so the tension is equal on all 4 legs
drill one more hole in the tube oustide the bedframe
insert and secure the lenght of rod.

to raise and lower wind the tube like a crank handle.
to secure tie a lenght of rope to the bedframe at a position where the rod handle of the tube passes. tie an eye in the rope and loop it over the rod handle.



with the

[RANDLOVER]

Have a look at these, kayak, ladder, bike hoists and roof box hoists.....

https://www.ebay.com.au/itm/395632892893?chn=ps&_ul=AU&_trkparms=ispr%3D1&amdata=enc%3A1Ympk9Kj_RMqdH5cNxUbt5Q6&norover=1&mkevt=1&mkrid=705-173151-935305-0&mkcid=2&mkscid=101&itemid=395632892893&targetid=2367800370202&device=m&mktype=pla&googleloc=1000339&poi=&campaignid=21776442415&mkgroupid=173963205248&rlsatarget=pla-2367800370202&abcId=10047386&merchantid=7364522&gad_source=1&gad_campaignid=21776442415&gbraid=0AAAAAD97CxR4UCtf8WRFVX764_-gMNhOn&gclid=EAIaIQobChMI7_fd0tbBjwMVKTF7Bx2xajRaEAQYAiAB EgKCp_D_BwE

Buy CyclingDeal Ceiling-Mounted Bike Hoist Rack Bicycle Hangers for Garage Storage | CD (https://www.cyclingdeal.com.au/buy/cyclingdeal-ceiling-mounted-bike-hoist-rack-secure/CD-KT09'scid=339721&utm_campaign=PaidShoppingAds&utm_medium=Shopping&utm_source=RL&utm_source=RL&utm_medium=Shopping&utm_campaign=VICCyclingDeal&scid=341567&gad_source=1&gad_campaignid=17416846962&gbraid=0AAAAACp3Cwj15dDvhBC-Mm0tqtsiJmMgo&gclid=EAIaIQobChMI7_fd0tbBjwMVKTF7Bx2xajRaEAQYBCAB EgK2_vD_BwE)

Harken 4 Point Hoister System - 40kgs (90lbs) Max Load HK7802 MonkeyFist Marine (https://www.monkeyfist.com.au/p/8968995/harken-4-point-hoister-system---40kgs-90lbs-max-load-hk7802.html?gad_source=1&gad_campaignid=206850206&gbraid=0AAAAADz8l2q6O7DSLmjpt9NqJWtbsfIkk&gclid=EAIaIQobChMI7_fd0tbBjwMVKTF7Bx2xajRaEAQYBSAB EgJPcPD_BwE)

Thule MultiLift - Kayak and Roof Box Lifter (https://www.a1roofracks.com.au/thule-multilift-572004?gad_source=1&gad_campaignid=22910735187&gbraid=0AAAAACZyJPNUP_uQrLFGhauWBCbxXKScR&gclid=EAIaIQobChMI7_fd0tbBjwMVKTF7Bx2xajRaEAQYFCAB EgJc6_D_BwE)

[RANDLOVER]

Also same sort of idea but different surfboard rack and attic ladder...

Surfboard Ceiling Rack – Connect Flooring (https://connectflooring.com.au/products/surfboard-ceiling-rack?variant=45155587621163&utm_source=google&utm_medium=cpc&utm_campaign=Google+Shopping&currency=AUD&country=AU&gad_source=1&gad_campaignid=22705045598&gbraid=0AAAAAqEz8TL-mrQieiJ_QgMg6HcnYbhNs&gclid=EAIaIQobChMI7_fd0tbBjwMVKTF7Bx2xajRaEAQYByAB EgIWCPD_BwE)

Bunnings Australia (https://www.bunnings.com.au/gorilla-2-1-3-05m-aluminium-attic-ladder_p0860794'region_id=118161&gclsrc=aw.ds&gad_source=1&gad_campaignid=21122993677&gbraid=0AAAAADtbEB8G2vMWJNHSpex94D6lugkdP&gclid=EAIaIQobChMIgPWwpdnBjwMVY9gWBR1xgB_wEAQYAiAB EgJLNvD_BwE)

[AK83]

Looking for a movable attic, storage for boxes, ladder, bikes and that important stuff I don't wish to throw away.

......
Looking for a smart way for DYI as I am tight [bigrolf]

Just after I built my shed(back in Coburg) I had the same idea. To use one of the corners of the ceiling as a movable storage platform.

Electric winch (from Bunnings cost less than $100), stainless cables, rollers(not eyes, for me), 50x2mm angle (already got the welder), 1200x2400 F14 formply.
All up was going to cost me $300, maybe $350 with some additional 'unexpected' hardware or something like that.

Mesh would have been better than formply but I couldn't easily find a supplier in my area. Bunnings was a min from my old place.

[NavyDiver]

Just after I built my shed(back in Coburg) I had the same idea. To use one of the corners of the ceiling as a movable storage platform.

Electric winch (from Bunnings cost less than $100), stainless cables, rollers(not eyes, for me), 50x2mm angle (already got the welder), 1200x2400 F14 formply.
All up was going to cost me $300, maybe $350 with some additional 'unexpected' hardware or something like that.

Mesh would have been better than formply but I couldn't easily find a supplier in my area. Bunnings was a min from my old place.

A friend built a electric salami drying rack hoist. Your helpful suggestion had me looking

250kg via double Giantz Electric Hoist Winch 125/250KG Cable 18M Rope Tool Remote Chain ? Oz Goods Depot (https://ozgoodsdepot.com.au/products/giantz-electric-hoist-winch-125250kg-cable-18m-rope-tool-remote-chain-lifting'msclkid=8b4a087acd78183c2a6060c6582bf093)
800k straight KINCROME Electric Lifting Hoist 400-800kg KP1202 | Total Tools (https://www.totaltools.com.au/102448-electric-lifting-hoist-400-800kg-kp1202)
2000kg via 12 volt at just over $100 may be my pick Buy ZESUPER Electric Winch 12V 4500LBS Synthetic Rope Wireless Remote Winch ATV UTV Boat 4WD Online | Kogan.com (https://www.kogan.com/au/buy/xbull-zesuper-electric-winch-12v-4500lbs-synthetic-rope-wireless-remote-winch-atv-utv-boat-4wd-aueb-zeew019/)

This is going to be fun [biggrin][biggrin] Found it. Kids work


https://www.youtube.com/watch?v=9UxhXnp1mcg

Little trivia time. Yesterday I was helping a mate put up his shed. We chatted about lifting the 3000 odd KG Anchor of HMAS Vampire by hand. Three triple blocks got about a metre pull on the cable. It TOOK HOURS :)

[AK83]

.....
This is going to be fun [biggrin][biggrin] Found it. Kids work ......

Yeah, I thought about timber too, but I had meters of 50mm angle for a few benches I made.
And I thought that using the angle inverted would allow me flexibility in allowing the specrite boards the ability to be moved around or removed with no fixings at all(just contained within the angled frame).

On the other side of the shed, I did use a 2.4 m length of the angle and a sheet of specrite in a fixed shelf/mezzanine, and that combo gives good strength for heavy loads and the ability to slide stuff to hard to reach back end.
Welded mesh would be more ideal in terms of strength vs weight, but harder to then slide stuff if that is a requirement too.

I had the added complexity of a gable roof(22deg) and 2.4m between trusses, so I'd have needed a couple of longitudinal supports for somewhere to anchor the rollers, AND also a couple of added rollers to take the low side wires along the trusses to the lifting point.
All doable ... just needed to find either the time or the inclination to get it done.

In the end it was an all round better option to move to a nicer location(with a nicer shed too, as a bonus).

current, much larger shed, is a bit easier for me, in that I'm looking at a mezzanine now, and making a lift/elevator type device to get up to it instead.