PDA

View Full Version : Auto guru to uprate ZF 4hp22 in Sydney?


up2nogood
5th April 2009, 05:23 PM
Just tossing it behind a 4.6 and figured I didn't really want to pull it out again and it is old.....

Anyone know of a transmission specialist in Sydney who can put the 4hp24 clutch packs in and do a service/rebuild without ballsing it up? Was going to send it to ZF, haven't spoken to them yet.
Disco_owner
5th April 2009, 05:35 PM
Just tossing it behind a 4.6 and figured I didn't really want to pull it out again and it is old.....

Anyone know of a transmission specialist in Sydney who can put the 4hp24 clutch packs in and do a service/rebuild without ballsing it up? Was going to send it to ZF, haven't spoken to them yet.

Hey Mate;

AFAIK , ZF only carry out a Standard Rebuild , another words they replace worn parts with OME parts. not sure if they put in heavy duty clutch pack out of a 4hp24 , assuming your existing one is 4hp22.
up2nogood
5th April 2009, 05:56 PM
Yep, existing is 4HP22.

So we need a guru then!
George130
6th April 2009, 06:57 PM
I know a guy in Canberra.
Vern
6th April 2009, 07:40 PM
Manuels in Thomastown, Vic. ZF specialists

Manuel Automatics Pty Ltd

353 Settlement Rd Thomastown VIC 3074
ph: (03) 9466 4499
dans
14th April 2009, 05:23 PM
Just out of interest.... who do you recommend in Canberra? My ZF went a bit erratic and one guy told me i needed to spend around $5k fixing it. However, after a service it has been fine so far for around another 30 to 40 thousand k's. But would rather take it to someone who knows for next service.

Dan
Pedro_The_Swift
14th April 2009, 05:29 PM
I know a guy in Canberra.

Hey Ed:D

did you ever post a list of gearbox mods?

or did you have to sign a non-disclosure?;):p
Slunnie
14th April 2009, 05:46 PM
When I had mine packed with all of the 4HP24 parts I had AMV do it and they sent it off somewhere, but just about everybody said that A&B transmissions (???) in Melbourne to do it. Apparently they are the guru's outside of ZF in Germany and ZF sends people there for training on the ZF transmissions.
George130
14th April 2009, 11:30 PM
Hey Ed:D

did you ever post a list of gearbox mods?

or did you have to sign a non-disclosure?;):p

I don't know half of the work done.
I do know that the new clutch packs have extra meat on them and there are more plates than in a standard box. Valve sprigs are heavier to.
It now has a custom oil pickup in the sump.
Since it was done at mates rates it was a case of only listing some of the work on the bill:D.
I did get a load of bits back for my amusement.
Blknight.aus
14th April 2009, 11:35 PM
Id take your auto to georges guy....

(hes had enough practice by now)
Pedro_The_Swift
15th April 2009, 03:06 PM
Id take your auto to georges guy....

(hes had enough practice by now)


X2:p
up2nogood
16th April 2009, 06:14 AM
I take it there's a story behind this somewhere.......
Blknight.aus
16th April 2009, 03:03 PM
there is....

but its painful to tell (if you happen to be George130) mildly amusing (if you are brand loyal to anything but a landy), funny (if your an automotive engineer) and educational (I use it as a "if you want to know what happens when you try to XXXX just as george130 what happened to his rig" kinda deal)

I'll let george tell the story as I tend to over emphasize some parts to highlight the importance of the particular point Im trying to make about doing certain modifications and how far you go with them.