Page 9 of 10 FirstFirst ... 78910 LastLast
Results 81 to 90 of 92

Thread: RaZz0Rs Bolt on's - Diesel RRC

  1. #81
    Join Date
    Mar 2008
    Location
    Bayswater, Melbourne
    Posts
    776
    Total Downloaded
    0
    And so shes done.

    This is "Bitsy" McRangieface

    Not much of her is really Rangie lol

    A few little things to do like every 4Wd - but for the most part shes done.



    TDI 300 from 98 Disco
    Rock crawler gears 30% reduction from Maxi drive
    Twin maxi lockers
    Maxi axles and rear axle housing
    Maxi drive Upgraded CV's
    5sp Manual suffix box
    2" Lift
    Snorkel
    120lt main tank

    List of things I added;

    Cleaned up and repainted my full roof rack
    Roof top tent
    Twin snorkle setup
    Rock sliders from Terrafirma
    Stacked draws and fridge slide for the rear from Off road systems
    Fit up my rear bar with wheel carrier
    Painted new bullbar
    New winch and light bars
    Roof console and FM radio pod
    Custom Audio setup 8 x speaker setup with 500w amp
    Third battery AGM deep cycle in a projector Power Hub battery box with 300w inverter
    Fitted cargo barrier and mounted 50mm higher
    Fit snow tires for snow trips
    Achilles - DESERT HAWK X MT 265/75/16's on standard rims - nice mudders now
    22lt water jerry
    Fit all my bash plates
    Diff breather kit
    Reverse camera and light (GPS does camera monitor)
    VMS HDX GPS
    Rubber flares right on to the guard
    Kept red poly bags to level out load in the rear
    Terrafirma 4 Stage adjustable shocks & heavy duty springs
    Terrafirma Silicon hose kit
    Switch block in place of radio space (Radio relocated to top of the Dash)
    Fuse box in the rear for Fridge, lights etc
    Replaced all Badges with ABS ones from the UK
    Added "Land Rover" seat belt covers and found some Land rover UK door protectors (Rubber stops)

    Front.jpgrear.jpg

  2. #82
    Join Date
    May 2014
    Location
    Tamworth NSW
    Posts
    4,291
    Total Downloaded
    0
    +10 internet points for the vehicle's name!
    I approve!
    -Mitch
    'El Burro' 2012 Defender 90.

  3. #83
    Join Date
    Mar 2008
    Location
    Bayswater, Melbourne
    Posts
    776
    Total Downloaded
    0

  4. #84
    Join Date
    Mar 2008
    Location
    Bayswater, Melbourne
    Posts
    776
    Total Downloaded
    0

  5. #85
    Join Date
    Mar 2008
    Location
    Bayswater, Melbourne
    Posts
    776
    Total Downloaded
    0

    Cool

    was trying to figure out how to get all the pics I uploaded here lol figured one way!

    Fitting new wheel carrier this weekend from LRA!

  6. #86
    Join Date
    Mar 2015
    Location
    Kyneton VIC
    Posts
    198
    Total Downloaded
    0
    Nice work, loving the mods.

  7. #87
    Join Date
    Dec 2014
    Location
    FNQ
    Posts
    1,016
    Total Downloaded
    0
    There's a lot of work in there!

    Could you tell me how the overhead console is for "intrusion" - i.e. does it interfere with head clearance etc or create any issues for visibility?

    I have considered this for quite some time and would take the opportunity to remove my headliner at the same time and make something similar.

    It looks good. I just wonder how big to make it.

  8. #88
    Join Date
    Mar 2008
    Location
    Bayswater, Melbourne
    Posts
    776
    Total Downloaded
    0
    Quote Originally Posted by Mercguy View Post
    There's a lot of work in there!

    Could you tell me how the overhead console is for "intrusion" - i.e. does it interfere with head clearance etc or create any issues for visibility?

    I have considered this for quite some time and would take the opportunity to remove my headliner at the same time and make something similar.

    It looks good. I just wonder how big to make it.
    Hey Merc

    If your not use to it and put ya head in first when ya jump in - you can hit ya head on it lol
    But other wise, once your seated its actually really good - the sides are angled inward so in the event of a crash - you aint hitting your head on it.

    Its a console I bought... 12 odd years ago from this forum - but could never use it - threw it in the shed and when I bought this one, I pulled it out and it all fit perfect and colour wasn't bad either.
    I tracked it to be from Department of the Interior Car Consoles & 4WD Storage Drawers overhead consoles roof consoles custom built consoles 4WD interiors storage systems vehicle consoles radio console dashboard pod four wheel drive but they haven't made one in over ten years. I bought a rivnut gun and put in 4 rivnuts in to the ribbing in the roof and bolted it up from there.
    ran power and CB wires up to it. Works awesome If you want I can measure it out - Its made from pine and thin ply - covered with a soft foam and vinyl.

    Didn't end up fitting the wheel carrier - coz I replaced the heater fan unit! Wow - big job lol mostly back together for driving and have a heater yay!
    I'll fit up that carrier next weekend and do more work on the dash.

  9. #89
    Join Date
    May 2018
    Location
    Geelong
    Posts
    28
    Total Downloaded
    0

    Tyres

    Bitsy McRangieface looks great!

    Any issues with rubbing the 265/75 16s on standard rims with 2 inch lift? I want to get this size and i'm hoping I can get away without having to get the wheels flipped.

    No body lift or fender cuts required? I'm not totally opposed to cutting, but the flares I bought mount under the lip so if i have to cut I cant use them.

  10. #90
    Join Date
    Apr 2012
    Location
    Here & There, WA
    Posts
    36
    Total Downloaded
    0

    old slot?

    Quote Originally Posted by RaZz0R View Post
    Radio install finally done - doing so while having a full on flu was kinda silly.. pleurisy has set in and steps away from Pneumonia

    But.. I think its looking good being on top of the dash Good mount for GPS as well.



    Attachment 127255Attachment 127256

    Hey razzor - you're an inspiration!

    I have had a new Alpine head unit in the cupboard for 2 years now but too scared to start pulling everything apart for fear nothing will go where I envisage. This could be an option. Can I ask:

    (a) where you got the caddy for your head unit;
    (b) what you put in the space left by the old one; and
    (c) have yo installed an amp and if so where did you locate that?

    Cheers
    Matt

Page 9 of 10 FirstFirst ... 78910 LastLast

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!