Page 10 of 11 FirstFirst ... 891011 LastLast
Results 91 to 100 of 107

Thread: What am I doing in this corner ????

  1. #91
    Join Date
    Oct 2011
    Location
    Sunshine Coast
    Posts
    1,224
    Total Downloaded
    0
    Threaded bellhousing hole is for wading plug they were supposed to be a proper 4x4. Re driving off the ramps- awesome! If I had a dollar for every stupid mistake or wrong decision What am I doing in this corner ????at least we’re still here doing silly stuff.

  2. #92
    Join Date
    Apr 2009
    Location
    Crafers West South Australia
    Posts
    11,732
    Total Downloaded
    0
    Gearbox with cast on bell housing would be Chrysler Torque-Flite 727, they also ran the solid front drive shaft to get clearance from the sump. Borg-Warners had bolt on bell housings.

  3. #93
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Other end of Banjo Tube, in engine bay, RH side. ????

    whitehillbilly
    Attached Images Attached Images

  4. #94
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Torque-Flite 727 it is then.
    New ball joint Rubber boots were in the tool box. Ball joints them selves seems really good.
    So pulled the steering rods apart, cleaned the ball joints up, sprayed in some grease, fitted new boots, then sprayed more in the top, to 'Pack' it.
    Had to tap out the two holes holing the steering dampener, under the axle housing.
    A NEW in packet, Tough Dog one in tool box. Could find anything wrong with original one,
    except needing new bushes, which I had, front one of my girls cars, so used them and fitted original one.
    Just new hoses, and bleed.
    Getting close.

    whitehillbilly
    Attached Images Attached Images

  5. #95
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Ordered hoses from MR Automotives, Redland Qld, yesterday at 10.30am. Arrived today.
    Great, helpful service. Apparently Uk made hoses, from good Uk supplier. ????
    Double the price of the cheapies.
    5 hoses, $12 postage.

    whitehillbilly
    Attached Images Attached Images

  6. #96
    350RRC's Avatar
    350RRC is offline ForumSage Silver Subscriber
    Join Date
    Mar 2008
    Location
    Bellarine Peninsula, Brackistan
    Posts
    5,501
    Total Downloaded
    0
    Quote Originally Posted by whitehillbilly64 View Post
    Ordered hoses from MR Automotives, Redland Qld, yesterday at 10.30am. Arrived today.
    Great, helpful service. Apparently Uk made hoses, from good Uk supplier. ????
    Double the price of the cheapies.
    5 hoses, $12 postage.

    whitehillbilly
    Goodridge braided hoses, guaranteed for life?

    DL

  7. #97
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0

    It goes and stops

    New hoses fitted. Secondary system bled up ok.
    Primary didn't.
    Only way was to have the motor running, then eventually it came good.
    couldn't stop the warning switch leaking. put in a small blanking plug.
    Down the paddock for a run. RH CV clicked a bit. Back up, filled up with oil, also checked Transfer box.
    No oil. Only two things I didn't check, but was on the list, before doing to much. 20/50 in Transfer case. OK ???? doing sort of flush, anyway
    Back in paddock, all things seemed.
    Shall I, yes causally down the road, nothing to much. Phone, in case a tow home was needed. couple of klms then back to a mates for a beer, before home. Brakes coming better with use.
    Squeaking fan belt needs adjusting. Back on ramps tomorrow to check for leaks.
    Also fitted the little fuel filter JS660, old one very dirty and a throw away one, in line after the main one.
    Ready for Blue slip, soon,I think.

    whitehillbilly
    Attached Images Attached Images

  8. #98
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Just investigating some oil leaks.
    Engine sump pan and auto gearbox pan had some bolts hand tight.
    Deagrease tonight after work.

    Whitehillbilly

  9. #99
    Join Date
    Oct 2011
    Location
    Sunshine Coast
    Posts
    1,224
    Total Downloaded
    0
    Leaks? On a Landrover ? Never heard of them - not leaking from somwhereWhat am I doing in this corner ????I’ve got diff oil from leaky rear diff pinion seal to clean up when I get home. And replace pinion seals front and rear.

  10. #100
    Join Date
    Oct 2014
    Location
    Northern NSW.Australia
    Posts
    2,023
    Total Downloaded
    0
    Hi,
    Need to replace LH flasher globe, on the dash.
    Easy job ????
    thanks

Page 10 of 11 FirstFirst ... 891011 LastLast

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!