Page 4 of 4 FirstFirst ... 234
Results 31 to 34 of 34

Thread: Using the disco a an off roader

  1. 20th November 2012, 01:03 PM #31
    Matplat
    Matplat is offline Master
    Join Date
    Nov 2008
    Location
    Brisbane
    Posts
    151
    Total Downloaded
    0
    Quote Originally Posted by Blknight.aus View Post

    find a suitable engineer and you can go up to 6 inch over size rubber with a 6 inch lift and a 4 inch body riser set.
    I'm gunna disagree with you there. Having recently looked into this myself I found the current rules from the dept of transport website, then spoke to a QLD based engineer.

    50mm larger is all you can go on diameter of tyres, and 50mm is all you can lift in springs, neither of which require an engineer certificate.

    You can do a further 50mm body lift however this will require an engineer certificate. It is however pretty pointless, as you can already fit the legal limit of tyre size without a body lift.
    Reply With Quote Reply With Quote
  2. 20th November 2012, 04:50 PM #32
    Blknight.aus's Avatar
    Blknight.aus
    Blknight.aus is offline RoverLord Vendor
    Join Date
    Aug 2006
    Location
    Melbourn(ish)
    Posts
    26,499
    Total Downloaded
    0
    not sure what got lost in translation but

    a, read the original statement again and b, Find a better engineer...

    theres more involved in it than just bolting on bigger tyres, the lift kit and the body blocks. but its doable and if the engineer approves it, documents it and plates it then its also on road legal.

    50+50+50 for a total of 150mm over stock height is the MAXIMUM you can do without requiring engineering certification. (and the body block lifts may now also be questionable)

    For a disco generally going a 2 inch lift and an extra inch of rubber (which only gives a half inch rolling radius increase) is as far as you go without having to start looking at brake lines, camel cuts, castor bushes, brake upgrades, drive line components. its also easier to get an early disco approved for a body lift than a later one.
    Dave

    "In a Landrover the other vehicle is your crumple zone."

    For spelling call Rogets, for mechanicing call me.

    Fozzy, 2.25D SIII Ex DCA Ute
    Tdi autoManual d1 (gave it to the Mupion)
    Archaeoptersix 1990 6x6 dual cab(This things staying)


    If you've benefited from one or more of my posts please remember, your taxes paid for my skill sets, I'm just trying to make sure you get your monies worth.
    If you think you're in front on the deal, pay it forwards.
    Reply With Quote Reply With Quote
  3. 21st November 2012, 01:30 PM #33
    Matplat
    Matplat is offline Master
    Join Date
    Nov 2008
    Location
    Brisbane
    Posts
    151
    Total Downloaded
    0
    First up, don't patronise me.

    If you read section LS9 part 1 in the link below you will see there is no allowance for increase of ride height beyond 125mm.

    It clearly states that 75mm in a combination of tyres and spring lift is the maximum allowable permitted without certification.

    http://www.tmr.qld.gov.au/~/media/Sa...s1112part1.pdf

    Please note of course that this is applicable to QLD only.

    If you can provide documentation to back your claim of 50+50+50 I would be more than happy to hear it!
    Reply With Quote Reply With Quote
  4. 21st November 2012, 07:19 PM #34
    Blknight.aus's Avatar
    Blknight.aus
    Blknight.aus is offline RoverLord Vendor
    Join Date
    Aug 2006
    Location
    Melbourn(ish)
    Posts
    26,499
    Total Downloaded
    0
    Quote Originally Posted by Matplat View Post
    50mm larger is all you can go on diameter of tyres, and 50mm is all you can lift in springs, neither of which require an engineer certificate.

    You can do a further 50mm body lift however this will require an engineer certificate. It is however pretty pointless, as you can already fit the legal limit of tyre size without a body lift.

    which nicely summates what I said the limits of what you can do without an engineer..


    Quote Originally Posted by Matplat View Post
    First up, don't patronise me.
    Since I cant patronise you, I'll challange you.

    http://www.infrastructure.gov.au/roa..._2011%20v3.pdf

    start there and begin digging here's a hint, the D1 in question does not have ABS brakes nor Airbags

    welcome to the squirrelly world that is ADRs, VSB, AS and NCOP, be careful of contradictions between the documents and applicable vehicle dats and versions.

    Have fun.
    Dave

    "In a Landrover the other vehicle is your crumple zone."

    For spelling call Rogets, for mechanicing call me.

    Fozzy, 2.25D SIII Ex DCA Ute
    Tdi autoManual d1 (gave it to the Mupion)
    Archaeoptersix 1990 6x6 dual cab(This things staying)


    If you've benefited from one or more of my posts please remember, your taxes paid for my skill sets, I'm just trying to make sure you get your monies worth.
    If you think you're in front on the deal, pay it forwards.
    Reply With Quote Reply With Quote
Page 4 of 4 FirstFirst ... 234
« RoofTop tent AND spare wheel | Cargo barrier mounting »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!