Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: Rear wheel bearing change. Hub stuck

  1. 15th August 2013, 06:16 PM #11
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    Seals are cheap
    Reply With Quote Reply With Quote
  2. 15th August 2013, 06:18 PM #12
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,777
    Total Downloaded
    1.13 MB
    Quote Originally Posted by sparky34 View Post
    OK, I will check first, 96 V8 only done 112,000 klms so hasnt been to the moon and back, seals should be good also?

    Thanks Sparky
    Bearings will be fine but as Damien said seals are cheap so may as well replace after repacking the bearings- 112k, its barely run in.
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
  3. 15th August 2013, 06:24 PM #13
    sparky34 Guest
    Thanks boys saved me a few dollars, new seals it will be.

    Saprky
    Reply With Quote Reply With Quote
  4. 15th August 2013, 09:00 PM #14
    mattg Guest
    So where does the little seal go?
    Reply With Quote Reply With Quote
  5. 15th August 2013, 09:30 PM #15
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    Back of the hub, after the bearing
    Reply With Quote Reply With Quote
  6. 16th August 2013, 07:58 AM #16
    mattg Guest
    ImageUploadedByTapatalk1376607322.476312.jpg
    Just here ?

    Can't do the 5 bolts up with this sitting over the axle. A bit puzzled about this.

    Matt
    Reply With Quote Reply With Quote
  7. 16th August 2013, 09:18 AM #17
    460cixy's Avatar
    460cixy
    460cixy is offline YarnMaster
    Join Date
    Oct 2006
    Location
    canberra
    Posts
    3,002
    Total Downloaded
    0
    Nope in the back side of the hub
    Reply With Quote Reply With Quote
  8. 16th August 2013, 09:31 AM #18
    weeds's Avatar
    weeds
    weeds is offline Swaggie
    Join Date
    Feb 2005
    Location
    Bracken Ridge - Brisbane - QLD
    Posts
    14,276
    Total Downloaded
    0
    i would call that the front of the hub....i.e. where you fit the wheel onto

    to remove the bearings and re-pack them you would have to have removed the hub seal which is on the back side of the hub i.e. diff side of the hub

    it looks llike you are hold up a lock washer? up against the outer bearing nut?
    Reply With Quote Reply With Quote
  9. 16th August 2013, 09:34 AM #19
    goingbush's Avatar
    goingbush
    goingbush is offline ForumSage
    Join Date
    Jul 2011
    Location
    Yarrawonga, Vic
    Posts
    6,568
    Total Downloaded
    0
    Reply With Quote Reply With Quote
  10. 16th August 2013, 05:22 PM #20
    mattg Guest
    Sorry not the best photo. This is for the rear bearings in case I am holding the little oil seal up against the the hole the axle goes in. The problem is the seal is just big enough to go over the axle but not go into the same hole but not Big enough to go over the thread against the nut. I see this as the front of the hub but can't get it to the back as it isn't going to go over the tread.
    Does anyone have an exploded view of the hub? Cheers Matt
    Reply With Quote Reply With Quote
Page 2 of 3 FirstFirst 123 LastLast
« Noisy lifters | EFI always on problem »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!