Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: CDL

  1. 8th December 2013, 06:32 AM #11
    Pedro_The_Swift's Avatar
    Pedro_The_Swift
    Pedro_The_Swift is offline The MOD Father
    Join Date
    May 2003
    Location
    On The Road
    Posts
    30,031
    Total Downloaded
    0
    The same problem can occur at the end of the drive,, move the selector but the CDL remains engaged,, reversing usually works. Take Note of the light and dont just drive off into the distance--
    "How long since you've visited The Good Oil?"

    '93 V8 Rossi
    '97 to '07. sold.
    '01 V8 D2
    '06 to 10. written off.
    '03 4.6 V8 HSE D2a with Tornado ECM
    '10 to '21
    '16.5 RRS SDV8
    '21 to Infinity and Beyond!

    1988 Isuzu Bus. V10 15L NA Diesel
    Home is where you park it..

    [IMG][/IMG]
    Reply With Quote Reply With Quote
  2. 8th December 2013, 10:01 AM #12
    steelo's Avatar
    steelo
    steelo is offline Master
    Join Date
    Jan 2008
    Location
    Pialba, Qld (near Hervey Bay)
    Posts
    288
    Total Downloaded
    0

    Talking

    My "light" hasn't worked for ages but CDL still engages
    Reply With Quote Reply With Quote
  3. 8th December 2013, 07:25 PM #13
    biglandy
    biglandy is offline Fossicker
    Join Date
    May 2012
    Location
    Gloucester,NSW
    Posts
    40
    Total Downloaded
    0
    Thanks again for all the advice, will give it another go over and see what happens ..cheers!
    Reply With Quote Reply With Quote
  4. 9th December 2013, 03:59 PM #14
    biglandy
    biglandy is offline Fossicker
    Join Date
    May 2012
    Location
    Gloucester,NSW
    Posts
    40
    Total Downloaded
    0
    Well she's all good working fine, light and all!!! Done a few circle's left,right then backwards a few noises,jacked it up and the wheel was clunking going around.So a bit more circle work,another clunk,jacked it up,another half a turn and she was locked in and light was on.Drove great...Sweet! Thank for advice.
    Reply With Quote Reply With Quote
  5. 10th December 2013, 08:00 AM #15
    steelo's Avatar
    steelo
    steelo is offline Master
    Join Date
    Jan 2008
    Location
    Pialba, Qld (near Hervey Bay)
    Posts
    288
    Total Downloaded
    0

    Wink

    Sooooo............. come on, what did you do??
    Reply With Quote Reply With Quote
  6. 11th December 2013, 04:31 PM #16
    sparky34 Guest
    Quote Originally Posted by steelo View Post
    I had the same prob when I bought mine, asked on here & was told to remove centre console (read manual for that) then you'll be at the bare metal. Either spray wd40 (or some-such) &/or put some hi-temp grease at base of shaft (in hollow), then just vigorously (very if have to) move it around.
    Worked for mine, I think mine was just a town car before I bought it & CDL was never or not used for a long time so ceased up metal to metal.
    Hope this helps a bit


    p.s. mines also a 96
    Mine was the same town car, when I bought it the guy I bought if of didn't know what the CDL lever actually did, few sprays with WD40 and in she went.
    Read on here someware that you either use it or loose it with CDL, so every time your in soft going operate the CDL.
    Do not try this on hard surfaces as mine suffers from windup in a big way. IE wont disengage
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Lifting a D1 | Master+Slave Cylinder & Front crank pulley replacement »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!