Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: A CDL Question of sorts....

  1. #1
    Join Date
    Jun 2009
    Location
    North Central Victoria
    Posts
    2,356
    Total Downloaded
    0

    A CDL Question of sorts....

    Hi,

    Have a 1999 auto td5 disco 2 with a Davis Performance Landy's actuator for the CDL. Ie It is 4wd in low only and all wheel drive in high. This suits me fine though (too much money to change to a proper kit). My question is that when I put it into Low and hence 4wd, no dash lights are coming on to indicate that the CDL is locked. Ive done some research on the forum and noticed someone else had a similar problem (but still different!).

    Ive taken it for a spin today on dirt and put the lever into low and nothing - no dash lights etc. Turned it off and on again and still no lights.

    What to do next??

  2. #2
    Join Date
    Feb 2009
    Location
    Rutherford AKA Maitland NSW
    Posts
    342
    Total Downloaded
    0
    The wiring for the light may not be hooked up.

    I sure someone will point you in the right direction but there is a plug that needs to be connected on the top of the transfer case and it might have been disconnected or is a dirty connection.

    Dazza

  3. #3
    Join Date
    Jun 2009
    Location
    North Central Victoria
    Posts
    2,356
    Total Downloaded
    0
    Cheers Dazza. Will check out the connection. Was just about to crawl under the car and have a look. Ive been too busy being Sadie to have a look yet!

    Cheers,

    Chris.

  4. #4
    Join Date
    Feb 2009
    Location
    Newborough, VIC
    Posts
    1,541
    Total Downloaded
    67.72 MB
    Quote Originally Posted by gusthedog View Post

    .............It is 4wd in low only and all wheel drive in high.
    .............
    Hi gusthedog,
    Discounting the effect of the traction control, with CDL in, it is technically 2wd (one front, one rear) unless you also have axle lockers.
    You need cdl plus axle lockers, front and back, for true 4wd.
    2002 D2 4.6L V8 Auto SLS+2" ACE CDL Truetrac(F) Nanocom(V8 only)

  5. #5
    Join Date
    Jun 2009
    Location
    North Central Victoria
    Posts
    2,356
    Total Downloaded
    0
    Quote Originally Posted by biggin View Post
    Hi gusthedog,
    Discounting the effect of the traction control, with CDL in, it is technically 2wd (one front, one rear) unless you also have axle lockers.
    You need cdl plus axle lockers, front and back, for true 4wd.

    I know this and have been explaining it to the un-initiated for years. However, it still does not answer my question.

    Im still confused why the dash wont light up. Ive crawled underneath and can see that the mechanism is working. Im thinking it must be the electrical connection. Anyone with any ideas apart from the switch?

  6. #6
    Join Date
    Feb 2009
    Location
    Rutherford AKA Maitland NSW
    Posts
    342
    Total Downloaded
    0
    Quote Originally Posted by gusthedog View Post
    Anyone with any ideas apart from the switch?

    Have you checked the bulb???

    Dazza

  7. #7
    Join Date
    Jun 2009
    Location
    North Central Victoria
    Posts
    2,356
    Total Downloaded
    0
    Stupidly no I havnt. Will check the bulb first thing tomorrow. Cheers dazza.

  8. #8
    Join Date
    Feb 2009
    Location
    Newborough, VIC
    Posts
    1,541
    Total Downloaded
    67.72 MB
    Quote Originally Posted by gusthedog View Post
    I know this and have been explaining it to the un-initiated for years. However, it still does not answer my question.

    Im still confused why the dash wont light up. Ive crawled underneath and can see that the mechanism is working. Im thinking it must be the electrical connection. Anyone with any ideas apart from the switch?
    Well it's got to be either the switch, or the wiring, or the lamp. Not likely to be the ECU.

    See this extract from RAVE:

    Differential lock unit switch operation
    When the differential lock unit switch is operated, an earth path is completed
    from the SLABS ECU pin C0506-9, via header C0761, to the differential lock
    unit switch on a BU wire.
    On vehicles with automatic transmission the earth path is completed from the
    switch on a B wire to splice joint SJ2. From the splice joint the earth is
    connected on a B wire to earth header C0552.
    On vehicles with manual transmission, the earth path is completed from the
    switch on a B wire to splice joint A33. From the splice joint the earth is
    connected on a B wire to earth header C0552.
    When the differential lock unit switch completes the earth path, the SLABS
    ECU interprets the earth as a signal. Simultaneously, the closure of the switch
    also completes an earth path from the instrument pack on a BU wire to header
    C0761, through the differential lock unit switch to the earth header C0552. This
    earth is used by the instrument pack to illuminate the differential lock warning
    lamp.

    Hope this helps.

    2002 D2 4.6L V8 Auto SLS+2" ACE CDL Truetrac(F) Nanocom(V8 only)

  9. #9
    Join Date
    Aug 2009
    Location
    Athens - Greece
    Posts
    200
    Total Downloaded
    0
    Quote Originally Posted by gusthedog View Post
    Hi,

    Have a 1999 auto td5 disco 2 with a Davis Performance Landy's actuator for the CDL. Ie It is 4wd in low only and all wheel drive in high. This suits me fine though (too much money to change to a proper kit). My question is that when I put it into Low and hence 4wd, no dash lights are coming on to indicate that the CDL is locked. Ive done some research on the forum and noticed someone else had a similar problem (but still different!).

    Ive taken it for a spin today on dirt and put the lever into low and nothing - no dash lights etc. Turned it off and on again and still no lights.

    What to do next??
    Have you tried to move the lever to the left?
    No matter if you 're on high or low range,disco is AWD and when the going gets tough you lock the cdl.
    The best test is to lift a wheel with a jack and turn it by hand and lock-unlock the cdl to see how it works.
    The other aspect is that maybe they connected the wrong wires-plugs to the cdl switch when they put the cdl kit.

  10. #10
    Join Date
    Jun 2009
    Location
    North Central Victoria
    Posts
    2,356
    Total Downloaded
    0
    fatman - the lever only moves from H to N to L and wont move to the left (like D1's and defenders). The Davis Performance product 'automatically' locks the cdl when you select Low unlike other cdl kits which have two cables and the capability to lock the cdl when you're in high. Although it does have restrictions, this system was only $180 bucks when I got it installed and has worked pretty good. I had the D2 in storage for 18 months while I was going around oz in my defender. The cdl kit worked the first few times I used it (around 2 years ago). I cant remember last time I saw the lights though.

    Ive checked the connections, globes, jacked it up and turned one wheel and I think there is a problem with the electric(kery) switch that tells the ECU that the cdl is locked. It cant be the wrong wires - as it has worked before. Also I have installed a switch to the black/blue wire that controls the Traction control (wire 9 on the central plug of slabs computer under the passenger side trim) . When switched off, the idea is that the ECU doesnt automatically turn the TC and ABS off when you restart the car anytime after locking the cdl. I can also turn the switch on - which means that I can cancel the TC by turning the car off, switching the switch to on, and then restarting the car (as is described at step 20 on www.discovery2.co.uk/Factory Diff Lock). At the moment when I turn the car off when in low, flick the switch on, and restart the car, the TC and ABS lights are not activating - hence my idea that there is a fault somewhere in the electrical system.

    Its starting to get beyond my mechanical and electrickery knowledge. I think that either the switch is buggered or I have a dirty connection maybe. The problem is I recently moved to Alexandra in Vic and my mechanic is in wodonga - 2.5 hrs north of here!

    Might have to visit someone in melbourne maybe. Can anyone recommend someone near belgrave (that's where my bro lives)? Thanks for all your responses by the way - its nice to have a good Land Rover community out there to rely on!

Page 1 of 2 12 LastLast

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!