Results 1 to 6 of 6

Thread: Ignition coil extension cable\harness

  1. 7th April 2014, 12:20 PM #1
    michaelp's Avatar
    michaelp
    michaelp is offline Fossicker
    Join Date
    Jun 2011
    Location
    Wyalkatchem
    Posts
    47
    Total Downloaded
    0

    Ignition coil extension cable\harness

    I was thinking of re locating the ignition coils for easy access and when i am changing to 4.6 it would be a convenient time.

    I would like to make up extension cables up for convenience.

    Does anyone know if you can buy the connectors,male and female.

    Or should i put in another type of connector in-line.

    Ref C0052,YCP107900


    2004 D2a V8
    Reply With Quote Reply With Quote
  2. 7th April 2014, 02:49 PM #2
    lewy
    lewy is offline Wizard Silver Subscriber
    Join Date
    Jan 1970
    Location
    darwin
    Posts
    1,502
    Total Downloaded
    0
    They are amp 3 pole junior connectors,the male is a bit hard to find.
    AMP Connectors/Terminals
    EFI Express : Bosch Style (Amp Junior Power Timer) 2 pin male connector kit - $6.00
    I have some at home to do the same thing have not got around to it yet,
    would love someone to make a kit though,would need the coil wires,plug leads and the mount to go between the valley cover to bolt the coils to.
    Reply With Quote Reply With Quote
  3. 8th April 2014, 07:30 AM #3
    Modelsp
    Modelsp is offline Master
    Join Date
    Dec 2012
    Location
    PRIMBEE, Wollongong NSW
    Posts
    336
    Total Downloaded
    0

    Multi cable waterproof connectors

    Try this site here for your connectors.
    Available in 1>>6 cables per plug/water resistant seals
    very easy to fit.
    cheers
    Paul

    10 SET CAR Boat Motorcycle Bike 4 WAY Waterproof Connector | eBay
    Reply With Quote Reply With Quote
  4. 8th April 2014, 10:52 AM #4
    lewy
    lewy is offline Wizard Silver Subscriber
    Join Date
    Jan 1970
    Location
    darwin
    Posts
    1,502
    Total Downloaded
    0
    They are very good connectors i have used them on the bike,But do they actually fit the coil packs.the male plug on the coil is part of the coil.
    Reply With Quote Reply With Quote
  5. 10th April 2014, 11:06 PM #5
    Roverlord off road spares
    Roverlord off road spares is offline AT REST
    Major part of the heart and soul of AULRO.com
     Vendor

    Subscriber
    Join Date
    Jul 2012
    Location
    Tecoma Vic
    Posts
    9,642
    Total Downloaded
    0
    Easiest solution would be to cut the wires and solder a length of wire between the cuts and heat shrink them, and use your existing plug on the coil,

    Reply With Quote Reply With Quote
  6. 11th April 2014, 10:17 AM #6
    clubagreenie's Avatar
    clubagreenie
    clubagreenie is offline TopicToaster
    Join Date
    Dec 2007
    Location
    Sydney, you know. The olympic one.
    Posts
    4,853
    Total Downloaded
    0
    Why when you can buy everything you need?

    Where are you planning on moving them to? Each one feeds both banks so there's a potential for needing very long leads.
    Reply With Quote Reply With Quote
« Rear ABS sensor wiring - different lengths? | Which head gasket? »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!