Page 1 of 8 123 ... LastLast
Results 1 to 10 of 76

Thread: SLS problem doing my head in

  1. 15th June 2015, 11:16 AM #1
    Timmy
    Timmy is offline Master Supporter
    Join Date
    Mar 2013
    Location
    Victoria
    Posts
    216
    Total Downloaded
    0

    SLS problem doing my head in

    So I've been chasing an SLS problem. Please don't tell me to change to coils, I actually changed back to SLS after the last owner converted.

    I've just changed both rear air bags for brand new contitechs. I've also replumbed the whole air harness from bags to compressor. Confirmed no leaks in either bag, or either fitting on each bag with soapy water.

    Car will stay inflated overnight. As soon as I unlock and open door, car will deflate to bump stops.

    I've swapped the left height sensor out for another used one as I was getting some strange readings on the nanocom (015 instead of 130 where I had set it). I think it may not have been plugged in correctly.

    So do people think it is height sensors or something in valve body, or even the slabs ecu?
    Reply With Quote Reply With Quote
  2. 15th June 2015, 12:32 PM #2
    lewy
    lewy is offline Wizard Silver Subscriber
    Join Date
    Jan 1970
    Location
    darwin
    Posts
    1,502
    Total Downloaded
    0
    Wow,this is a new one,watching with interest,I presume you can hear air being exhausted when you open the door.
    Will it stay inflated if you leave it unlocked overnight.
    unhook the battery for half an hour whilst it is inflated,see if it droppes when you hook the battery up,dont forget the radio code.
    Reply With Quote Reply With Quote
  3. 15th June 2015, 12:34 PM #3
    Timmy
    Timmy is offline Master Supporter
    Join Date
    Mar 2013
    Location
    Victoria
    Posts
    216
    Total Downloaded
    0
    Yep sure can!
    Reply With Quote Reply With Quote
  4. 15th June 2015, 12:53 PM #4
    Barefoot Dave's Avatar
    Barefoot Dave
    Barefoot Dave is offline Wizard Subscriber
    Join Date
    Oct 2008
    Location
    Heart in the Deep Nth of FNQ,Body in the Deep Nth of Brisneyland
    Posts
    1,623
    Total Downloaded
    0
    Can't think of all the options in the slabs menu, but why don't you try a factory reset? I get the impression that it may have been programmed to allow a Shorty easy access/ egress.
    Cheers, BDave.
    Replace "You are...!", with "Are you...?"

    Army Land Rover Buyers Guide.
    buymilitaryvehicles.com

    Reunited with RFSV 51 680, 'Sleazy'!!
    '00 VeryDisco TD5 Auto,
    Nanocom Evo for D2 TD5 and Puma
    Gone:RFSV, 51-699, Carryall 48-358.
    Reply With Quote Reply With Quote
  5. 15th June 2015, 12:55 PM #5
    Timmy
    Timmy is offline Master Supporter
    Join Date
    Mar 2013
    Location
    Victoria
    Posts
    216
    Total Downloaded
    0
    That's a good thought.
    I actually have a late model slabs ecu to go in when I convert cdl. Maybe I should just put that in now!
    Reply With Quote Reply With Quote
  6. 15th June 2015, 01:01 PM #6
    lewy
    lewy is offline Wizard Silver Subscriber
    Join Date
    Jan 1970
    Location
    darwin
    Posts
    1,502
    Total Downloaded
    0
    Have you told the slabs that you have put the air back in
    Reply With Quote Reply With Quote
  7. 15th June 2015, 01:05 PM #7
    Timmy
    Timmy is offline Master Supporter
    Join Date
    Mar 2013
    Location
    Victoria
    Posts
    216
    Total Downloaded
    0
    Sure have. It has been working for a few months now. Sorry, WAS working...
    Reply With Quote Reply With Quote
  8. 15th June 2015, 01:07 PM #8
    gusthedog's Avatar
    gusthedog
    gusthedog is offline ChatterBox
    Join Date
    Jun 2009
    Location
    North Central Victoria
    Posts
    2,356
    Total Downloaded
    0
    How old is the firmware on your nanocom? I had exactly the same issue and it turned out to be that the auto height setting wasn't being stored in the car due to issues with my nanocom's software being old. Essentially (from memory here and it was 3 years ago) when you set the height you had to select the reset to bumpstops setting rather than saving the height as the buttons had been reversed on the screen but not in the software. So choosing one actually meant selecting the opposite. Does that make sense? I found the firmware issue on one of the UK forums. Updating the nanocom sorted my issue. Might be worth checking.
    Reply With Quote Reply With Quote
  9. 15th June 2015, 01:09 PM #9
    Timmy
    Timmy is offline Master Supporter
    Join Date
    Mar 2013
    Location
    Victoria
    Posts
    216
    Total Downloaded
    0
    I have just updated to the latest (1.29 from memory). As I also had read that issue.
    I swear I've read every single post on sls ever written now haha!
    The confusing part for me is that it happens when opening the door, which is possibly waking up the slabs?
    Reply With Quote Reply With Quote
  10. 15th June 2015, 01:11 PM #10
    Roverlord off road spares
    Roverlord off road spares is offline AT REST
    Major part of the heart and soul of AULRO.com
     Vendor

    Subscriber
    Join Date
    Jul 2012
    Location
    Tecoma Vic
    Posts
    9,642
    Total Downloaded
    0
    Tim maybe it's some how switching through to TRANSPORT MODE, this will lower to the bumpstops. You did do a lift in suspension didn't you, did you fit the level arm spacer to raise the height of the ARM on the Lever?
    Cheers,
    Mario

    Reply With Quote Reply With Quote
Page 1 of 8 123 ... LastLast
« Winch power | D2a Td5 Head »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!