Reply With QuoteMate you are a gentleman. Thank you
Master
SubscriberNah don't do that. I'll measure everything over the weekend and get back to kyou.
TRS Chip ,D2a I/c, Silcone Hoses, EMS2, 2" Lift, BFG KM2s, QT Diff Guards, 4X4 DE Guard, Shadow Bar. VRS Winch, LR Light Guards, .50 CDL, Provent 200, Slickrock Disconnects, Rovadrive Sump, G4 Roof Rails, D2a SLABS ECU, APT Sliders.DBA Rotors. ABS Ext.
ForumSage
SubscriberMate you are a gentleman. Thank you
Master
SubscriberRighty Ho Lads,
Apologies for the delay as I was trying to get the drawers system below finished for an upcoming tripand also to Slunnie for hijacking this thread, but I'm assuming it has helped somewhat.
http://
To find the mounts place a 12 inch ruler vertically down from the wee plastic trim clips as shown in the pics, about 270mm down is where the mounts are.
The rear one is about 5mm offset from the clip......
http://
The front one lines up with the trim clip.....
http://
Hope that helps and good luck with the project, if you need anymore help flick me a PM.....
Cheers Dave
TRS Chip ,D2a I/c, Silcone Hoses, EMS2, 2" Lift, BFG KM2s, QT Diff Guards, 4X4 DE Guard, Shadow Bar. VRS Winch, LR Light Guards, .50 CDL, Provent 200, Slickrock Disconnects, Rovadrive Sump, G4 Roof Rails, D2a SLABS ECU, APT Sliders.DBA Rotors. ABS Ext.
Swaggie
Fantastic, thanks Dave! Do you recall by any chance the bolt size?
Cheers
Slunnie
~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
The MOD Father
I think 10mm,, but its been a while Slunnie
"How long since you've visited The Good Oil?"
'93 V8 Rossi
'97 to '07. sold.
'01 V8 D2
'06 to 10. written off.
'03 4.6 V8 HSE D2a with Tornado ECM
'10 to '21
'16.5 RRS SDV8
'21 to Infinity and Beyond!
1988 Isuzu Bus. V10 15L NA Diesel
Home is where you park it..
[IMG][/IMG]
Master
SubscriberFrom memory I'm thinking it was a M8 x1.25 x 30mm ( Although I guessing you go a 40mm?) Grade 8.8 HT....Countersunk as I needed the head to sit flush against inner edge of the battery tray......Originally Posted by Slunnie
Something like this one below .....
http://
TRS Chip ,D2a I/c, Silcone Hoses, EMS2, 2" Lift, BFG KM2s, QT Diff Guards, 4X4 DE Guard, Shadow Bar. VRS Winch, LR Light Guards, .50 CDL, Provent 200, Slickrock Disconnects, Rovadrive Sump, G4 Roof Rails, D2a SLABS ECU, APT Sliders.DBA Rotors. ABS Ext.
Master
SubscriberI made some wee tabs like this to weld up to the tray and align with the mounts...
http://
http://
It all relatively easy to make a rear tray, even with rudimentary welding skills, a steel one could be knocked up in a day. I made mine in aluminium because I had access to an AC Tig at the time and because I like to be flash lol
Cheers Dave
TRS Chip ,D2a I/c, Silcone Hoses, EMS2, 2" Lift, BFG KM2s, QT Diff Guards, 4X4 DE Guard, Shadow Bar. VRS Winch, LR Light Guards, .50 CDL, Provent 200, Slickrock Disconnects, Rovadrive Sump, G4 Roof Rails, D2a SLABS ECU, APT Sliders.DBA Rotors. ABS Ext.
Swaggie
Fantastic, thanks again!
Cheers
Slunnie
~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
ForumSage
SubscriberThat's awesome Dave. Thanks mate. Cheers
Excellent fabrication....
Your opinion on 17kg vibrating against only 2 mounts for 100s of kilometres? Have you done this yet?
Posting Permissions
| Search AULRO.com ONLY! |
Search All the Web! |
|---|
|
|
|
Bookmarks