Page 2 of 8 FirstFirst 1234 ... LastLast
Results 11 to 20 of 77

Thread: 3d printer

  1. #11
    Join Date
    Jul 2014
    Location
    PERTH, WA
    Posts
    354
    Total Downloaded
    0

    D2 Gutter Ends / Rear Corners

    Quote Originally Posted by rick130 View Post
    Umm, isn't that what these are? 3d printer
    I think that what Incisor pictured is the roof-gutter END, where the guttering stops at each upper corner of the windscreen.
    So, at the front of the car.
    One end slides into the guttering, the other forms an open spout.

    I was asking whether there might also be a model for the piece that goes around the rear corners, so one end would tuck into the side guttering, and the other into an end of the rear guttering section.

  2. #12
    Join Date
    Apr 2002
    Location
    Godwin Beach 4511
    Posts
    20,688
    Total Downloaded
    32.38 MB
    Quote Originally Posted by rick130 View Post
    3d printer
    needs lots of supports to print
    2007 Discovery 3 SE7 TDV6 2.7
    2012 SZ Territory TX 2.7 TDCi

    "Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
    "If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
    'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
    “What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
    "We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
    "The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius

  3. #13
    Join Date
    Jul 2014
    Location
    PERTH, WA
    Posts
    354
    Total Downloaded
    0

    Rick130's internet connection might be faster than mine!

    "Snap"!

  4. #14
    Join Date
    Apr 2002
    Location
    Godwin Beach 4511
    Posts
    20,688
    Total Downloaded
    32.38 MB
    some photos and measurements and i could possibly get something sorted...

    measurements with a vernier preferred
    2007 Discovery 3 SE7 TDV6 2.7
    2012 SZ Territory TX 2.7 TDCi

    "Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
    "If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
    'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
    “What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
    "We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
    "The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius

  5. #15
    Join Date
    Jan 1970
    Location
    NSW far north coast
    Posts
    17,285
    Total Downloaded
    0
    Quote Originally Posted by incisor View Post
    some photos and measurements and i could possibly get something sorted...

    measurements with a vernier preferred
    We'll see what we can do.

  6. #16
    Join Date
    Apr 2002
    Location
    Godwin Beach 4511
    Posts
    20,688
    Total Downloaded
    32.38 MB
    first prototype print of one of the front bits

    printed.. with supports still attached

    IMG_0915.jpg

    roughly cleaned up

    IMG_0916.jpgIMG_0917.jpg

    this was printed in draft mode
    2007 Discovery 3 SE7 TDV6 2.7
    2012 SZ Territory TX 2.7 TDCi

    "Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
    "If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
    'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
    “What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
    "We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
    "The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius

  7. #17
    Join Date
    Jan 1970
    Location
    NSW far north coast
    Posts
    17,285
    Total Downloaded
    0
    Looking at the photos in the Britcar site the rear corners are part of the long side, the pieces up and over the rear door are separate.
    Both of those parts are now obsolete but NOS is kicking around.

    I'm putting an order in to Mario tomorrow for some other bits and pieces so I'm asking if he's able to source anything so we can then use that as a pattern.

  8. #18
    Join Date
    Jul 2014
    Location
    PERTH, WA
    Posts
    354
    Total Downloaded
    0

    Prototype 3-D Print

    Phenominal!

    Can I ask how long the printer worked to produce that prototype?

    Andrew


    Quote Originally Posted by incisor View Post
    first prototype print of one of the front bits

    printed.. with supports still attached

    IMG_0915.jpg

    roughly cleaned up

    IMG_0916.jpgIMG_0917.jpg

    this was printed in draft mode

  9. #19
    Join Date
    Apr 2002
    Location
    Godwin Beach 4511
    Posts
    20,688
    Total Downloaded
    32.38 MB
    Quote Originally Posted by AndrewMilne View Post
    Phenominal!

    Can I ask how long the printer worked to produce that prototype?

    Andrew
    that was done in draft mode so only took 3.5hrs

    a final print will take 4hrs a side then 20 mins to clean up when you remove the supports etc
    2007 Discovery 3 SE7 TDV6 2.7
    2012 SZ Territory TX 2.7 TDCi

    "Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
    "If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
    'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
    “What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
    "We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
    "The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius

  10. #20
    Join Date
    Jan 1970
    Location
    NSW far north coast
    Posts
    17,285
    Total Downloaded
    0
    Really cool.

    I just spoke to Mario and he sold the last one he could get last year

Page 2 of 8 FirstFirst 1234 ... LastLast

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!