Page 4 of 4 FirstFirst ... 234
Results 31 to 36 of 36

Thread: M R Automotive Recovery points?

  1. #31
    Davo is offline ChatterBox Silver Subscriber
    Join Date
    May 2007
    Location
    WA
    Posts
    2,595
    Total Downloaded
    0
    Pirate4x4.Com - Extreme Four Wheel Drive This may be helpful - there's a good illustration of how not to use a shackle, about halfway down?
    At any given point in time, somewhere in the world someone is working on a Land-Rover.

  2. #32
    Join Date
    May 2010
    Location
    brighton, brisbane
    Posts
    33,853
    Total Downloaded
    0
    Quote Originally Posted by Tank View Post
    if I was in the market for underbody tow points I would go hooks with new appropriately sized bolts or the slotted ARB offerings, Regards Frank.
    I asked ARB about hooks, they agreed hooks were definately suitable for recovery points, however advice from their engineers was that proper advice must be sought on just where on the chassis they are mounted, as the chassis , at that point, may have to be strenghtened, to take the force associated with recovery. Bob
    I’m pretty sure the dinosaurs died out when they stopped gathering food and started having meetings to discuss gathering food

    A bookshop is one of the only pieces of evidence we have that people are still thinking

  3. #33
    Join Date
    May 2010
    Location
    brighton, brisbane
    Posts
    33,853
    Total Downloaded
    0
    Heard something yesterday from someone in the 4wd dealer business, he said the reason ARB were spending up big on getting the engineering done to test & certify recovery points is because legislation is in the pipeline to certify aftermarket parts [radius arms, etc] to meet a new Australian standard. Now, this is hearsay at this point, I can't find anything official, but it makes sense. Why would ARB spend BIG money certifying recovery points if it is not necessary under the current Aus. standards or ADR requirement? When you see the new recovery points done so far cost between $200 -$ 250, could be an expensive exercise . Perhaps someone might be able to enlighten us further on this. Bob
    I’m pretty sure the dinosaurs died out when they stopped gathering food and started having meetings to discuss gathering food

    A bookshop is one of the only pieces of evidence we have that people are still thinking

  4. #34
    Join Date
    Sep 2007
    Location
    Gold Coast
    Posts
    6,078
    Total Downloaded
    0
    Quote Originally Posted by Disco Muppet View Post
    far as i know philco doesn't make them anymore.
    Philco is still making them I believe and has some stock. He has been away a bit in NZ but I think is back now so it could be worth sending him a PM

  5. #35
    Join Date
    Feb 2005
    Location
    Bracken Ridge - Brisbane - QLD
    Posts
    14,276
    Total Downloaded
    0
    Quote Originally Posted by bob10
    Heard something yesterday from someone in the 4wd dealer business, he said the reason ARB were spending up big on getting the engineering done to test & certify recovery points is because legislation is in the pipeline to certify aftermarket parts [radius arms, etc] to meet a new Australian standard. Now, this is hearsay at this point, I can't find anything official, but it makes sense. Why would ARB spend BIG money certifying recovery points if it is not necessary under the current Aus. standards or ADR requirement? When you see the new recovery points done so far cost between $200 -$ 250, could be an expensive exercise . Perhaps someone might be able to enlighten us further on this. Bob
    Umm, either way ARB will try and convince us we needed to upgrade.

  6. #36
    Join Date
    May 2010
    Location
    brighton, brisbane
    Posts
    33,853
    Total Downloaded
    0
    Quote Originally Posted by weeds View Post
    Umm, either way ARB will try and convince us we needed to upgrade.
    Probably through that action magazine, where it's not a real 4wd until it has every mod. known to man. I often wonder if those 4wd's are put over the weighbridge, to check how close they are to their max weight. But, in all seriousness, if indeed that becomes legislation, I don't think it would matter which company it was, all would have to comply. It would then be illegal to produce certain after market parts unless they complied to the Aus. standard & ADR. Could the Gov. make it retrospective? I don't think so, but I'm not a Lawyer. Bob
    I’m pretty sure the dinosaurs died out when they stopped gathering food and started having meetings to discuss gathering food

    A bookshop is one of the only pieces of evidence we have that people are still thinking

Page 4 of 4 FirstFirst ... 234

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!