Stickers, AULRO

They are a bit brighter than the previous ones which were more discreet on Rangies . [bigrolf]

Attachment 132092

Quote:

---

Originally Posted by Roverlord off road spares

They are a bit brighter than the previous ones which were more discreet on Rangies . [bigrolf]

Attachment 132092

---

you know you need to take that top layer off ?

https://www.aulro.com/afvb/images/im...017/11/329.jpg

Quote:

---

Originally Posted by incisor

you know you need to take that top layer off ?

---

Yes Inc, discovered that today, taking the top layer off also lifted some of the letters from the screen and now a few bubbles.[bigsad] will have to get the zit pin out and let the air out [bigrolf]
Attachment 132133

Quote:

---

Originally Posted by Roverlord off road spares

Yes Inc, discovered that today, taking the top layer off also lifted some of the letters from the screen and now a few bubbles.[bigsad] will have to get the zit pin out and let the air out [bigrolf]

---

Based on the last ones purchased about 3 years ago, I'm going to try a different approach this time. I'll use a plastic sleeve and put them on the inside rear windows ie not stick them down. Then maybe they wont fall apart gradually in the sun/weather?

Quote:

---

Originally Posted by gavinwibrow

Based on the last ones purchased about 3 years ago, I'm going to try a different approach this time. I'll use a plastic sleeve and put them on the inside rear windows ie not stick them down. Then maybe they wont fall apart gradually in the sun/weather?

---

My old ones never peeled in fact when I sold the D2 I couldn't even remove it with a razor blade, but they were not vinyl cut.
I think its all in the application.
No instructions on how to apply, I have in the past put vinyl cut decals on my boat hull and used a squirt of soapy water, then fit the decal and squeegy to apply. not sure on these ones if you can use that method or whether you have to fit them dry?
Inc might weigh in.

Thanks Dave got mine yesterday

Quote:

---

Originally Posted by Roverlord off road spares

My old ones never peeled in fact when I sold the D2 I couldn't even remove it with a razor blade, but they were not vinyl cut.
I think its all in the application.
No instructions on how to apply, I have in the past put vinyl cut decals on my boat hull and used a squirt of soapy water, then fit the decal and squeegy to apply. not sure on these ones if you can use that method or whether you have to fit them dry?
Inc might weigh in.

---

there are full instructions in the stickers thread in the verandah :p

Here you go.....

Quote:

---

Originally Posted by incisor

I am told the stickers will finally be delivered to me tomorrow if all goes to plan...

Once we get them they will be mailed as quickly as we can get them out.

Instructions for fitting them below

Quote:

---

Sign industry standard
Installation of stickers




You will need:
Metho
Clean rag (something that won't leave lint)
Measuring tape or ruler
Masking tape
Stiff plastic card with straight edge, like a credit card.
(Signwriters use application squeegees )


Method

1. Clean surface the sticker is to be installed. Remove all marks, grease, oil and foreign objects. Give a final wipe with metho and wait a few seconds to dry.
2. Place your sticker on a flat surface and run over the top clear tape to make sure all lettering is adhered to clear application tape.
3. Place sticker on the substrate​​ you want to install it to, with backing paper still on.
4. Use a ruler to position it where you want it to go
5. Use masking tape to go across the top of sticker and substrate. This holds it in position. Try to get half the tape on the sticker and the other half on the substrate.
6. Flip the sticker over. The tape will hold in place.
7. Peel the paper backing off.
8. Flip sticker back over, avoiding touching the surface and keeping light tension. Hold it as close to the surface as you can without touching.
9. Use your card, starting from the tape at the top and apply pressure. Work your way down the sticker
10. Remove making tape.
11. Remove clear application tape.

If you have any bubbles in the vinyl, you can leave in the sun. Heat helps remove them. If the bubbles are still there you can pop with a pin and smooth out.

---

and a little movie for you

AULRO Stickers.mp4

---

Mine arrived today, thank you for all your efforts.