Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: Series 3 109

  1. #1
    Join Date
    Sep 2006
    Location
    Perth
    Posts
    18
    Total Downloaded
    0

    Post Series 3 109

    Hi, been on the forum a while but not much action until now. I have finally dragged my 109 out of storage and the task of getting her running again has begun, a lot easier now it is home and not and hours drive away. Here is the run down so far:

    1974 Series 3 109
    Registered
    Holden 186 conversion
    - Appears to be a Seatons conversion
    - HEI ignition
    - No chassis cutting or modification
    Has an interesting oil filter plumbed in through the oil pressure sender hole and back in through the sump. This will go as it leaks badly (has been great for chassis preservation over the years though)
    Oil sump has been modified to hold more oil maybe? has a another 1/2" plug on the drivers side.
    Electronic ign and a 350 Holley.

    Immediate Tasks
    - Cooling system overhaul
    - Braking system overhaul
    - Clutch hydraulics overhaul
    - Rear X member repair (should get away with a few patches)
    - New oil/filters/plugs
    - New tyres (second hand)

    Once these are done it will be drive able and roadworthy. I have set myself a budget of $1500 to get her back on the road as i have some of the parts already.

    Long Term Tasks
    Fuel system overhaul
    Simplify/tidy up/modernise electrics
    Bulkhead repairs Only a minor amount of rust around passenger side windscreen and drivers footwell (thanks to a leaky Clutch MC)
    Suspension overhaul
    Attached Images Attached Images

  2. #2
    Homestar's Avatar
    Homestar is offline Super Moderator & CA manager Gold Subscriber
    Join Date
    Aug 2010
    Location
    Sunbury, VIC
    Posts
    20,055
    Total Downloaded
    0
    Always good to get the motivation to dust off an old project and get stuck back in. 👍😊
    If you need to contact me please email homestarrunnerau@gmail.com - thanks - Gav.

  3. #3
    Join Date
    Sep 2006
    Location
    Perth
    Posts
    18
    Total Downloaded
    0

    Radiators

    Thanks, hope the motivation hangs around!

    Pulled out the radiator today and it is stuffed. Lucky I had a spare that looked OK, however it was tested and it leaks from the core.......bugger.

    Radiator shop quoted $550 for a re core, which shoots a massive hole in the budget. There seems to be a mixed bag of results from ebay aluminium radiators and the Land Rover to Holden ones seem to have tripled in price since I last looked. I like the idea of a Torana radiator and they seem reasonably priced for the ally knock offs.

    Anyway here is my collection of stuffed radiators. I might strip them down, keep the tanks and scrap the cores. They may be useful.
    Attached Images Attached Images

  4. #4
    Join Date
    Sep 2006
    Location
    Perth
    Posts
    18
    Total Downloaded
    0

    factory six cylinder

    I had my suspicions that my Land Rover may have been a six cylinder from the factory, but was not sure owing to the fact that I have not seen many two door 109's in this configuration. The fact that the chassis was not cut for the Holden conversion, the shape of the lift pump under the drivers seat and the factory oil cooler behind the grill raised my attention, however I though the six cyl had a dual circuit braking system (mine does not).

    Clifton scientific confirms that the 943 prefix on the chassis number is indeed a six cyl. The next phase of my investigation will be to pull the front wheels and check the brake diameter.

  5. #5
    Join Date
    Jan 1970
    Location
    Narre Warren South
    Posts
    6,314
    Total Downloaded
    0
    The radiator looks like a Series III 4-cyl one, reasonable price from the UK but shipping adds considerably Radiator 2286cc/4cyl Standard type (3 core) - Paddock Spares
    Most of the local LR suppliers will keep them.

    The front brakes were wider on the 6-cylinder. You only have to look at the brake drum to determine which it is..... the standard 11" has a wide chamfer on the outer edge the wider 6-cylinder ones don't have the chamfer. I'll take a picture tonight if I remember.


    Colin
    '56 Series 1 with homemade welder
    '65 Series IIa Dormobile
    '70 SIIa GS
    '76 SIII 88" (Isuzu C240)
    '81 SIII FFR
    '95 Defender Tanami
    '58 Series II (sold)
    Motorcycles :-
    Vincent Rapide, Panther M100, Norton BIG4, Electra & Navigator, Matchless G80C

  6. #6
    Join Date
    Apr 2015
    Location
    Adelaide
    Posts
    110
    Total Downloaded
    0
    Nice car! That looks like an oil cooler behind the front grill?

    Should be able to tell wether it was a 6 or 4 by the bulkhead shape - particularly the removable panels around the gear stick lever.

    Good luck with the budget - I failed at that!

  7. #7
    Join Date
    Apr 2014
    Location
    Blair Athol, Adelaide South Aust.
    Posts
    2,745
    Total Downloaded
    0
    You can buy new radiators from between $250 and $450 locally if you look around on ebay.

    Cheers Rod

  8. #8
    Join Date
    Jan 1970
    Location
    Narre Warren South
    Posts
    6,314
    Total Downloaded
    0
    Front brake drum differences 6-cyl & 4-cyl LWB are shown below.

    As mentioned, the bulkhead and panels round the gearstick are different but you'd need pictures to show the differences.

    Brake Drums by Colin Radley, on Flickr

    6-Cylinder bulkhead


    Another 6-cylinder (Series III)
    DSCN3996 by Colin Radley, on Flickr

    4-Cylinder bulkhead



    Colin
    Last edited by gromit; 17th January 2018 at 09:15 PM.
    '56 Series 1 with homemade welder
    '65 Series IIa Dormobile
    '70 SIIa GS
    '76 SIII 88" (Isuzu C240)
    '81 SIII FFR
    '95 Defender Tanami
    '58 Series II (sold)
    Motorcycles :-
    Vincent Rapide, Panther M100, Norton BIG4, Electra & Navigator, Matchless G80C

  9. #9
    Join Date
    Jan 2008
    Location
    Goodna QLD
    Posts
    291
    Total Downloaded
    0
    Quote Originally Posted by ashc View Post
    Hi, been on the forum a while but not much action until now. I have finally dragged my 109 out of storage and the task of getting her running again has begun, a lot easier now it is home and not and hours drive away. Here is the run down so far:

    1974 Series 3 109
    Registered
    Holden 186 conversion
    - Appears to be a Seatons conversion
    - HEI ignition
    - No chassis cutting or modification
    Has an interesting oil filter plumbed in through the oil pressure sender hole and back in through the sump. This will go as it leaks badly (has been great for chassis preservation over the years though)
    Oil sump has been modified to hold more oil maybe? has a another 1/2" plug on the drivers side.
    Electronic ign and a 350 Holley.

    Immediate Tasks
    - Cooling system overhaul
    - Braking system overhaul
    - Clutch hydraulics overhaul
    - Rear X member repair (should get away with a few patches)
    - New oil/filters/plugs
    - New tyres (second hand)

    Once these are done it will be drive able and roadworthy. I have set myself a budget of $1500 to get her back on the road as i have some of the parts already.

    Long Term Tasks
    Fuel system overhaul
    Simplify/tidy up/modernise electrics
    Bulkhead repairs Only a minor amount of rust around passenger side windscreen and drivers footwell (thanks to a leaky Clutch MC)
    Suspension overhaul
    Looks tidy. Those engine mods look interesting. I've always thought remote oil filter is a good idea where it hard to get at, but that's not a problem in a LR with a golden.
    The extra sump is also interesting, maybe the PO extended to oil pickup into the mini sump for when at odd angles off-road. Not sure how much benefit it would have for the effort though. Maybe don't ditch the setup just yet.
    I always had over heating issues with my Holden/LR setup, maybe adding an oil cooler inline with the remote filter could help with cooling. Just a thought.

  10. #10
    Join Date
    Jan 2008
    Location
    Goodna QLD
    Posts
    291
    Total Downloaded
    0
    Quote Originally Posted by ashc View Post
    Thanks, hope the motivation hangs around!

    Pulled out the radiator today and it is stuffed. Lucky I had a spare that looked OK, however it was tested and it leaks from the core.......bugger.

    Radiator shop quoted $550 for a re core, which shoots a massive hole in the budget. There seems to be a mixed bag of results from ebay aluminium radiators and the Land Rover to Holden ones seem to have tripled in price since I last looked. I like the idea of a Torana radiator and they seem reasonably priced for the ally knock offs.

    Anyway here is my collection of stuffed radiators. I might strip them down, keep the tanks and scrap the cores. They may be useful.
    I had no end of trouble with Torana rads, they just couldn't keep up with the cooling. Maybe the alloy ones would make the difference, but not confident.
    I ended up finding a recon GQ patrol 4 core at the wreckers. Much better cooling, but still got hot on slow hill climbs.

Page 1 of 2 12 LastLast

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!