Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Stromberg Holden Carburettor Leaks

  1. #11
    Join Date
    Sep 2012
    Location
    Westlake ,brisbane
    Posts
    3,922
    Total Downloaded
    0
    Quote Originally Posted by Homestar View Post
    Kits for these are universal and contain all the parts for most models - you’ll find you’re left with a pile of parts from the kit once your done. Last time I did one the kit was $14 - not sure what they run to these days, it’s been about 15 years since I did one.

    Let us know how you get on. 👍
    I bought a kit from Repco last year , almost had a hart attack when he told me the price. It was more than $30 & am thinking about $60 for the kit. I almost didn't buy it but I was doing a favour for a friend who has developed Dementia & was trying to get his S2 running so the family could sell it.

  2. #12
    Join Date
    Jan 1970
    Location
    Irymple, Victoria, Australia
    Posts
    2,900
    Total Downloaded
    0
    Lionel if your putting a kit through the carby it is also advisable to hone the top cover on a piece emery or wet n dry paper sitting on a piece of glass. The tops are prone to warping and allowing air to be suck in, you wont get it running perfect if the top is warped. Honing them is easy and takes only a few minutes to do.

    Secondly you can run an engine at idle with top removed from a Stromy to check the fuel level and make sure the needle and seat are not leaking, you just need a small tab of cardboard to place over the air venturi to make it run even. But don't rev the ring out of the engine whilst doing this or you might get fuel spillage onto the manifold.

    With a kit through them and in good tune, which is easy to do, they are a trouble free carby.

    Cheers, Mick.
    1974 S3 88 Holden 186.
    1971 S2A 88
    1971 S2A 109 6 cyl. tray back.
    1964 S2A 88 "Starfire Four" engine!
    1972 S3 88 x 2
    1959 S2 88 ARN 111-014
    1959 S2 88 ARN 111-556
    1988 Perentie 110 FFR ARN 48-728 steering now KLR PAS!
    REMLR 88
    1969 BSA Bantam B175

  3. #13
    Lionelgee is online now YarnMaster Silver Subscriber
    Join Date
    Mar 2010
    Location
    Queensland
    Posts
    3,814
    Total Downloaded
    0
    Hello All,

    In the cool light of morning the engine started first press of the starter button. I stopped the motor once the petrol started flowing out of the bottom of the carburettor. After taking the top off I found the float chamber full and overflowing with the float up as high as possible. As A Kelly and others suggested the fuel is leaking over the accelerator pump linkage.

    I put everything back together and waited about ten minutes. The engine started again after the first press of the starter button. If the engine stalls and the button is pressed immediately it will not start. Wait until sufficient fuel has leaked out of the carburettor and the engine starts first push of the button. So it is the float levels and related fuel level adjustments.

    When I first started with Land Rovers with Holden motors I tried to head off a problem with carburettors by getting a mechanic to fully re-kit the carburettor that came fitted on the vehicle. The first thing the carburettor did when it was returned to the motor was to leak fuel out the bottom.

    Later when I learnt how to read the codes I identified that it was a 149 carburettor fitted to the 202 motor.

    Looks like a rebuild kit is in order.

    Kind regards
    Lionel

  4. #14
    Join Date
    Mar 2013
    Location
    East Gippsland
    Posts
    990
    Total Downloaded
    0
    Try cleaning the needle and seat you have the same problem I had with float chamber overflowing
    I didn’t change float level as all was good after crud was removed ,if you Carefully remove brass union that fuel pipe nipple screws into from carbie body inside is a three cornered needle pushed in and out by a tab on the float.
    Looks a bit like a button from float side when in carbie
    took about three seconds to blow out union on my bench and all was good......could save you the cost of a kit, and resetting float level

    Cheers Paul

  5. #15
    Join Date
    Feb 2007
    Location
    Cooroy, QLD
    Posts
    1,383
    Total Downloaded
    0
    Try bending the float tab down a smidgen, that may solve the issue. At lease enough that fuel isn't dripping onto the exhaust while you get a rebuild kit.

  6. #16
    Join Date
    Mar 2013
    Location
    East Gippsland
    Posts
    990
    Total Downloaded
    0
    Guess what...... started my engine to get it up to running temperature and the carbie started overflowing again
    So I pulled top off and the float chamber and it was brimming with fuel, pulled the fuel pipe union off and another piece dirt stopping needle seating, I replaced all the fuel pipe before the filter and used an old short piece after the filter when I replumbed the fuel lines. This must be the cause of my problem

    Cheers Paul

Page 2 of 2 FirstFirst 12

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!