Scott if you still have them do you mind reposting those photos you took? All the links are now broken. Have found this on a lot of old photos lately.Quote:
Originally Posted by LRD414
Cheers
Printable View
Scott if you still have them do you mind reposting those photos you took? All the links are now broken. Have found this on a lot of old photos lately.Quote:
Originally Posted by LRD414
Cheers
It's a problem with all photos in the AULRO Gallery from before it changed to https that's still being worked on.Quote:
Originally Posted by Russrobe
Apparently they'll return once an issue with Tapatalk is fixed.
But here's a few of them anyway .... (won't work on Tapatalk, should be ok on main site)
https://www.aulro.com/afvb/images/im...017/02/469.jpg
https://www.aulro.com/afvb/images/im...017/02/470.jpg
https://www.aulro.com/afvb/images/im...017/02/471.jpg
https://www.aulro.com/afvb/images/im...017/02/472.jpg
https://www.aulro.com/afvb/images/im...017/02/473.jpg
Cheers,
Scott
I do like the look of the genuine LR flaps. Logo to be seen for all those green with envy followers..... ;)
Fronts don't need to be fancy so it'll be the homemade or D1/2s for them.
Now all I need is more money....... maybe the Cook will go back to work. :o
AlanH.
60 bucks each from Southerns.Quote:
Originally Posted by ATH
D1 fronts were $40 delivered
1 job down. Now just to fit the cb, 2 aerials and run cables.https://www.aulro.com/afvb/images/im...017/02/432.jpg
I just had to get a wheel alignment because my castor was out that badly the RF had already knocked out the plastic clips where the screws had to go!!!
All good now =) Thank god I got that done, was toeing in 10mm!https://www.aulro.com/afvb/images/im...017/02/433.jpg
Used some of these big flat washers.
https://www.aulro.com/afvb/images/im...017/02/434.jpg
Dodgy temporary fix for the inner guard behind the bull bar. Don't know what to do with that. Maybe just a big lump of silicon
I want some. What exactly should I be asking Southern for - is it Defender 90 TD5 rear mud flaps?Quote:
Originally Posted by Russrobe
I used Sika - Body Panel Adhesive and pulled flush against protection plate. Neat and hasn't budged, but I have drilled a couple of holes in the back lip of the plate and will fit the white plastic clips from the OEM front bumper over the inner guard and screw through to them. I'll try find a pic of those white screw clips.Quote:
Originally Posted by Russrobe
I ended up with 2 of the same onesQuote:
Originally Posted by Ferret
.
Below is what other people have used:
"I ordered them from Rimmer Bros UK, part numbers as follows:
LR055332
CAT500450PMA"
I have 2 x LR055332 which fits both sides, you just have to make a cut out for the exhaust with a good pair of side cutters. Think they were around $70ea inc gst
Fronts look for Discovery 1 mud flaps, $40
Hope they last a while!
Hmm, I kind of need that gap that's all as if you push it flush with the steel plate, the guard goes out of it's original shape on mine and the tyres rub.Quote:
Originally Posted by Mungus
That solid mass in there atm is actually Paint Shield lol Sets like a rock again after removing, can see how it stops pin stripes.
Might need a bit more trimmed off? Mine sits flush without distortion. Took a couple of attempts to get the trimming right though.
Fitted my D1 front flaps today and looks good. Backs (Defender flaps) were done a couple of weeks ago. Haven't put up pics as they look the same as others who've used the flaps from other models.
Now to get the Dee dirty over Easter and see if they work.
Thnx. for all the tips on how to do it.
AlanH.