What happened to your D3/D4 today?

Printable View

Show 40 post(s) from this thread on one page

13th May 2020, 06:08 AM
josh.huber

Quote:

Originally Posted by LRD414

I gave up on those Bremtec Euro pads and replaced with the Pedders ceramic. Properly bedded in, etc, etc, just couldn’t get them to stop squeaking at low speed. The Pedders ones come from the same factory as the highly regarded Akebono ones. Recently installed their rotors and pads to the front too.

Scott

I too hate a low speed squeal, I pulled out my TRW pads to read the part numbers and they are the standard pads not the DTEC ceremic ones recommend to me on here. So I ordered a set yesterday. Hoping to get rid of that noise. Brake dust doesn't bother me. But the standard TRW pads definitely are dusty.
14th May 2020, 03:44 PM
DiscoJeffster

Quote:

Originally Posted by josh.huber

I too hate a low speed squeal, I pulled out my TRW pads to read the part numbers and they are the standard pads not the DTEC ceremic ones recommend to me on here. So I ordered a set yesterday. Hoping to get rid of that noise. Brake dust doesn't bother me. But the standard TRW pads definitely are dusty.

I had to buy from the UK to get ceramic. I couldn’t find a local supplier I trusted to send me the correct product.
14th May 2020, 06:39 PM
josh.huber

Quote:

Originally Posted by DiscoJeffster

I had to buy from the UK to get ceramic. I couldn’t find a local supplier I trusted to send me the correct product.

I bought from UK but they refunded it. Nil stock. Then found an Aus seller website. Much cheaper.. Once I confirm they are dtec cotec I'll share the link
15th May 2020, 05:00 PM
ian4002000

Quote:

Originally Posted by josh.huber

I bought from UK but they refunded it. Nil stock. Then found an Aus seller website. Much cheaper.. Once I confirm they are dtec cotec I'll share the link

I put a set of Repco pads in my D3 recently and they are great. They have an extra anti noise coating and the pads stop great. I removed a set of Aussie made 4wd pads that wouldn't pull the car up fast enough.

Ian
Bittern
16th May 2020, 01:31 PM
DiscoDB

Updated the firmware on the IIDTool today which was long over due. I do like the height control functionality.

Programmed the buttons at minus 20, plus 20 and plus 40 for now. Already have the GOE rods fitted but this is so much easier and quicker.
16th May 2020, 03:19 PM
ChookD2

3 Attachment(s)

Quote:

Originally Posted by INter674

Pictures when fitted..that's what 😉

Here ya go....

Attachment 160926 Attachment 160927 Attachment 160928
16th May 2020, 03:25 PM
INter674

Looks good☺ thanks
17th May 2020, 08:18 PM
Narangga

Quick run to Woolies for a battery for the water level meter on the camper trailer because we're going camping next weekend. :banana: :banana: :banana:
18th May 2020, 06:25 AM
Tombie

What happened to your D3/D4 today?

Someone decided they wanted to try and have a look inside.

They had already ransacked several vehicles in the area.
My Alexa unit is linked to my Cameras and notified me there was someone skulking about. Went out and was confronted by 4 individuals who were now across the road and had broken into the neighbours vehicle.

Chased them down, now all in lock up.

https://uploads.tapatalk-cdn.com/202...5bf3f13bc8.png https://uploads.tapatalk-cdn.com/202...e36984e54f.png https://uploads.tapatalk-cdn.com/202...64e404b958.png
18th May 2020, 06:57 AM
scarry

Quote:

Originally Posted by Tombie

Chased them down, now all in lock up.

Well done.

But no doubt they will be out today and back at it in a day or two.:censored::censored:

Show 40 post(s) from this thread on one page