Servicing a D3 on the ground

**BradC** · 26th July 2020, 12:01 PM

I have a stahlbus. I thought about cutting an access panel into the bash plate but I quite like having a good look around while the oil is draining. Now I have the right bolts on the bash plate ( all sorts of dodgy and missing crap when I bought the car ) I now have a little routine. Spin them out with the rattle gun and it’s off super quick, they go back in with fingers to start the thread and hang the plate, and then a quick buzz with the air ratchet to do them back up.

**RobMichelle** · 26th July 2020, 02:31 PM

So the stahlbus is still protected by the bash plate?

**SeanC** · 26th July 2020, 03:16 PM

Originally Posted by Eric SDV6SE

I am sooo glad the D4 has the top suction tube, oil changed in 20 min, no need to get underneath the car at all.

The Fumoto or Stahlbus drain valves are handy, but IMHO anything like that sticking out underneath is asking for trouble, might as well not bother with the bash plates.

I have a Stalhbus and it fits under the bash plate.

For services I use 4 ramps and any suspension work I have 4 stands but only jack the front or back up so I don’t have the entire vehicle supported by the stands. Have a 2500kg trolley jack. Wouldn’t go any lighter.

**Tombie** · 26th July 2020, 05:03 PM

Originally Posted by Eric SDV6SE

I am sooo glad the D4 has the top suction tube, oil changed in 20 min, no need to get underneath the car at all.

The Fumoto or Stahlbus drain valves are handy, but IMHO anything like that sticking out underneath is asking for trouble, might as well not bother with the bash plates.

No problem with the Stalhbus - and a small hole through the bash plates has it sorted. It certainly won’t get hit offroad or on.

No pump to clean, no waiting. 5 min from lifting bonnet to new oil and filter in.

**Tombie** · 26th July 2020, 05:08 PM

**RobMichelle** · 26th July 2020, 05:18 PM

Oooh I’m liking that Tombie for sure

I’ll source one this week hopefully and for when I do service. Mmm5 min is that including fuel filter

.

**101RRS** · 26th July 2020, 05:21 PM

Any body got a link for buying Stalhbus in Australia? Also what size is needed for a 2.7 TDV6?

Thanks

Garry

**SeanC** · 26th July 2020, 06:01 PM

Originally Posted by Tombie

No problem with the Stalhbus - and a small hole through the bash plates has it sorted. It certainly won’t get hit offroad or on.

No pump to clean, no waiting. 5 min from lifting bonnet to new oil and filter in.

Yep. I have cut a hole in the bash plate too. I cover the hole with some wide cloth tape to keep sand out. So far it has stayed on between services.

**DiscoJeffster** · 26th July 2020, 06:15 PM

Originally Posted by Tombie

No pump to clean

Never cleaned mine - simply drain it into an oil bottle like an oil pan. Sure gravity is quicker, but the additional ten minutes allows me to drink two additional beers. I think I’m on the winner.

**Tombie** · 26th July 2020, 06:32 PM

Originally Posted by RobMichelle

Oooh I’m liking that Tombie for sure

I’ll source one this week hopefully and for when I do service. Mmm5 min is that including fuel filter

.

Fuel filter is another 5 min.

Thread: Servicing a D3 on the ground

Thread Tools

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions