EGR eradication confusion RRS 2007 TDV8 3.6l

Quote:

---

Originally Posted by peterjj

I had an IID Tool so bought the EGR delete software from Bell Auto Services and some blanking plates from a ? place in UK off ebay.
You do not remove the EGRs, just remove pipes from EGRs to inlet and fit blanks to EGR and inlet holes. Also need to cut off the butterflies that is at the entrance to the inlet manifold. So that bit is not reversible.
Easy enough to do it all yourself if you have played with mechanical things yourself in the past. The guy from BAS (Peter) responds nicely to silly questions too.
I think the EGR Delete software from BAS also includes a mild throttle response update, could be wrong but feels like it and think i read it somewhere. Can pay for and apply the software for a tune-up at the same time.
EGR delete is not for a performance improvement but helps stop carbon build up in the manifold and restricting performance as the engine gets older.
Anyway I have had no problems after it being installed for about 3 years.

---

Why did you go to all the extra work physically on the egr's rather than just the remap being enough ?

Quote:

---

Originally Posted by haydent

Why did you go to all the extra work physically on the egr's rather than just the remap being enough ?

---

Fitting the blanking plates and cutting off the the inlet butterfly as well as the software was the instructions. Maybe the software doesn't stop things working, just stops errors after you fit blanking, but that's just a wild guess. You could confirm with BAS if the physical blanking is still required.

Quote:

---

Originally Posted by peterjj

Fitting the blanking plates and cutting off the the inlet butterfly as well as the software was the instructions. Maybe the software doesn't stop things working, just stops errors after you fit blanking, but that's just a wild guess. You could confirm with BAS if the physical blanking is still required.

---

I contacted Pete, at BAS, and unless your egr is sticking open with errors, the software patch is all you need to disable egr function.

The issue on some vehicles was that the EGR had already failed and as such then needed to be blanked, often if the EGR is still functioning you can just turn them off in the ECU.

But that's just my understanding.

I have just had mine done last week. There was an error on one of the valves but this has since been cleared along with a remap done on a dyno. The valves have been programmed to stay closed and also physically locked.

Yes, it does run much better, but I'm not sure how much is contributed to the remap. It is nice to not have the engine light on though!

Pre remap 195Kw and 617Nm

Post remap 226Kw and 715Nm

:burnrubber:

Quote:

---

Originally Posted by haydent

can you confirm you tried only blanking first yourself and got errors ?

---

I can not first hand confirm that. I was advised by my competent Inde that would be the case and I went with that.

My brother blanked his MY08 TDV8 RRS after performance issues pointed to a leaking EGR valve. The electrical connectors are still fitted and the pcm is original. The RRS is used almost entirely to tow his van and has had no issues since blanking the EGRs.

Hey Graeme, I was curious where you wrote about your Brother Blanking off his EGR.

And wanted to ask, did he just simply remove the EGR link up pipes on both sides, Blank them with plates. And start the car and Drive...
And whether he has had any lights on the dash or codes since..

There doesn't seem to be a definitive answer on the internet anywhere, if this is a possibility on a Sport 3.6 TDV8.
So many conflicting reports about , "yes you can" , "no you cant" Having to tune it out .

Just looking for someone who has first hand knowledge of someone having done it , with no ongoing issues...

Thanks mate.. Regards Marty.

He inserted plates at the valve outlets - the pipes are still fitted.
No faults or messages are displayed with his stock ecu. Note that L322 and RRS fault handling for this engine are not necessarily the same.

Quote:

---

Originally Posted by mtb_gary

Does anyone know of a Perth based diesel tuner that has successfully completed the EGR blanking and retune on a 2007 TDV8

---

Delayed response but if you are still looking

Jordan Rover Tech in Perth

Davis Performance in Sydney - Bruce Davis did my 2007 TDV8 years ago when an EGR failed - blanked EGR's and a mid range re-map - amazing improvement in performance and being careful, could get down near 8l/100km on a trip, even with +200,000km on the clock

Recently checked hourly rates in Perth of a few different Idie's - Jordan the most cost competitive and with a top reputation, but still well above East coast Indie hourly rates.