Thread: A/C Compressor & Condenser Change Pics & Notes

Next step, compressor removal:

Drain a few litres out of the radiator:
20221227_131153.jpg
Remove upper cover, intercooler pipes and fan:
20221227_132014.jpg
You must disconnect some upper radiator pipes to do this:
Also compressor marked with arrow:
20221227_132047.jpg
Another view of compressor through wheel arch:
20221227_135952.jpg
Removal of belt:
20221227_140708.jpg
Removal of turbo heat shield and mount, gives access for hand around rear of strut:
20221227_141406.jpg

Disconnect and relocate ac lines, replace orings.
20221227_144712.jpg
Removal of turbo supply joiner:
20221227_142758.jpg
Disconnect and move back solid turbo supply pipe, rotating helps:
20221227_144345.jpg

This was a hard bit, remove rear bolt, I used a ratchet strap to hold metal turbo output pipe a bit further away from pump to give better access, 1/4" ratchet with knuckle
20221227_154403.jpg
Releasing the turbo supply pipe from the lower fan shroud was tricky, I ended up pulling them both out
This is to make room for the pump to get past when removing through hood.
20221227_161920.jpg

Now you can take out the 2 front bolts on the pump and the pump itself:
(shown with pulley removed, this should not be necessary)
20221227_162038.jpg

The amount of oil I drained out of the pump:
20221227_172804.jpg

Sad to see metal flecks:
20221227_172814.jpg
20221227_172903.jpg
I decided to open up the drier to see what it was like inside:
To my pleasant surprise I found the desiccant is not that big, and the flow does not go through it, but more importantly there isa screen filter that all the flow goes through:
20221228_155017.jpg
It was intact with quite small holes, it just slides out through the bottom of the tube, so it could be slid out to inspect without cutting the tube.
20221228_155140.jpg

All the flow from the condenser flows through the drier (as tested with air compressor), the flow goes into the drier tube first, and then out through the filter, so there as plenty of space in the tube cavity for junk/debris build up.

20221228_155025.jpg

One would expect no significant metal pieces would make it through the condenser and drier screen, so this made me more confident in just only replacing them, rather than the whole ac system, evaporator included as recommended by denso/lr , but this would have been too much work (including removing the complete interior) without trying just replacing these parts first.

I was also not able to flush the parts not changed, due to the TX valve being under the dash, though some say it can be flushed (slowly) past, if I was going to try this I would check with my AC tech if he would be ok pulling a vac on the system for longer and getting any solvent left behind, I was just afraid of solvent getting into the pump on trip into town.

I did put the air pump on the open system pipe in normal flow direction to check TX valve wasnt blocked and what the flow rate would be like if i tried to flush past.

How long it will last only time will tell, fingers crossed, its currently re-gassed and making cold again.

Cant edit my original post, so heres the parts list, please confirm what part numbers you need, I ordered from lrparts.net , keep in mind its cheaper to split your parts into separate orders if you can get each one under $1000, as then you dont have to pay import duty, gst and customs fees.

Denso 7SEU17C Compressor LR014536
Condenser with dryer LR018405
O-rings JUU500020 x2 , JUU500010, JUU500040

(If I had my time again id look into getting a cheap used or new 7SEU17C body that fits another common car and swap the differing parts over from my dead pump)

Here is a screenshot of my ac pressure from car off, to start car with ac on full.


Screenshot_20221231-103201_IIDControl.jpg

Interested to hear if this is still working? Was it a compressor imploding that caused this issue to start with? Cheers

Originally Posted by Discoproc1

Interested to hear if this is still working? Was it a compressor imploding that caused this issue to start with? Cheers

The pressures on the graph are way too high,so something else is definitely not right.

Originally Posted by Discoproc1

Interested to hear if this is still working? Was it a compressor imploding that caused this issue to start with? Cheers

still working, the compressor would intermittently jam, snapping the sacrificial pulley connection so the pulley just spun free

Originally Posted by scarry

The pressures on the graph are way too high,so something else is definitely not right.

how do you know that ? we've been considering getting the gas weighed and topped up just to check in on it, pretty sure they check the pressures then.

i can do another test with the gap tool again

Originally Posted by haydent

still working, the compressor would intermittently jam, snapping the sacrificial pulley connection so the pulley just spun free



how do you know that ? we've been considering getting the gas weighed and topped up just to check in on it, pretty sure they check the pressures then.

i can do another test with the gap tool again

Looking at the graph,pressures anywhere near 3000KPA,are not normal,looks like it could be cycling on the safety switch?

Maybe this only happens on start up,but still not good.