Results 1 to 4 of 4

Thread: L322 rack seal on column shaft

  1. 14th September 2023, 10:13 AM #1
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0

    L322 rack seal on column shaft

    Has anyone replaced the seal on the column shaft? No genuine part is listed in Microcat.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  2. 14th September 2023, 02:20 PM #2
    p38arover's Avatar
    p38arover
    p38arover is offline Major part of the heart and soul of AULRO.com
    Administrator
    I'm here to help you!     Gold Subscriber
    Join Date
    Jan 1970
    Location
    Western Sydney
    Posts
    30,704
    Total Downloaded
    1.63 MB
    Not me.

    I’ve never looked at it. Maybe a power steering service mob?
    Ron B.
    VK2OTC

    2003 L322 Range Rover Vogue 4.4 V8 Auto
    2007 Yamaha XJR1300
    Previous: 1983, 1986 RRC; 1995, 1996 P38A; 1995 Disco1; 1984 V8 County 110; Series IIA



    RIP Bucko - Riding on Forever
    Reply With Quote Reply With Quote
  3. 14th September 2023, 02:52 PM #3
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    I found an ebay seller of rack seals who has identified the necessary seal from the ZF part number for the rack. It looks as though it's nothing special that couldn't be purchased from a local bearing supplier but having the correct seal on hand avoids having no transport while I wait for the correct seal or reconditioned rack then having to get someone to deliver it. I'll post the seal number when it arrives then hopefully later confirm that it fits.
    I found an overhaul document for a couple of similar ZF racks which shows the input shaft bearing and seal components.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  4. 23rd September 2024, 06:27 PM #4
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    The seal is a standard 20x30x5 double-lip, pressed into a plate retained by a circlip. I used hydraulic pressure to move the plate partly out, presumably stopping when the o-ring around the plate got as far as the circlip groove. The plate was removed using a small pick between the shaft and the plate, successively lifting one side then the other.
    The shaft is covered by a plastic alignment cap without any useful dust ingress prevention. It was refitted with layers of felt that may or may not help. The seal plate provides a well that had accumulated dust/mud so perhaps less dust will now get in.

    Contrary what is stated in the workshop manual, the steering pump can easily be removed without disconnecting the nearby a/c pipe. The pump removal was indirectly related to replacing the seal (my error).
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
« Weird Central Locking Problem | 05 TO 12 Range Rover BULL BAR IF YOU LIKE IT !!!!!!!!!!!!!!! »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!