LR has obviously renamed the connector since the early L494 diagrams but it has the same wire colours and cavity positions.
Finally found the info I have been looking for. Obviously the access rates for TOPIX vary according to the recency of the model, the newer the more expensive.
The brake controller connector is located up above the brake pedals. Just need to find out the plug to suit and should be fairly straight forward.
Here is the image but the link might display a little clearer.
https://www.flickr.com/photos/639420...dateposted-ff/
Cameron
If in doubt, throttle out
MY16 RRS SE SDv6
MY16 Ranger XLT
2008 911 GT2 - dream came true
1976 Escort mk2 - race car
LR has obviously renamed the connector since the early L494 diagrams but it has the same wire colours and cavity positions.
MY12 RRV 4.4 TDV8 AB, +LLAMS, +e-diff, +ACC stop/go. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
VK2HFG and APRS W1 digi
Will do a proper DIY once I get my act together. Needs to be done before 23 Sept as off for a couple of weeks in the caravan on the beach up north. Hopefully the dealer will know which plug I need to go into the connector. Should be a fairly simple job after that.
Cameron
If in doubt, throttle out
MY16 RRS SE SDv6
MY16 Ranger XLT
2008 911 GT2 - dream came true
1976 Escort mk2 - race car
This is the special part you need to fit into the landrover connector.
Tekonsha 3035-P Brake Control Wiring Adapter for Ford by Tekonsha
Search for it on Amazon, sells for about $10.
The red plastic divider can be "persuaded" from this connector, then wires can be swapped to mate up with the landrover pinouts.
Cheers
On the diagram, what does "Connector housing not serviceable" mean?
Cheers,
Sean
“Only two things are infinite, the universe and human stupidity, and I'm not sure about the former.” - Albert Einstein
Sean,
I stand to be corrected but I think it means it cannot be used for anything else.
I spoke to the service guys at the dealer about getting a plug to connect to the wires so I could then connect to the connector (excuse pun), but they were not particularly helpful. Will be speaking to Redarc tomorrow to see if they also have a specific plug/wire setup like Tekonsha.
Cameron
If in doubt, throttle out
MY16 RRS SE SDv6
MY16 Ranger XLT
2008 911 GT2 - dream came true
1976 Escort mk2 - race car
I can only assume that as the connector comprises of more than 1 part, the individual parts are not available as generally the complete housings (without pins or sockets) are available as spare parts. Connectors that are just a simple housing are usually described as serviceable. Pins or sockets with wire stubs are also generally available as repair kits but are positively expensive, eg $120 for a packet of 10.
MY12 RRV 4.4 TDV8 AB, +LLAMS, +e-diff, +ACC stop/go. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
VK2HFG and APRS W1 digi
Hi guys
Sorry to Hijack this for my L405 but Graeme and Brick - I just want to double check the wiring. I know my tow pro wiring intimately: red = brake lights, blue = brakes on trailer, white = earth and black = 12v power to tow pro unit.
I just want to ensure I have them heading to the correct colours on the pins under the dash in the L405 Rangie. I have also become very adept at swapping the pins around on that tekonsha/ford plug I got from Amazon - again, thanks Graeme.
So from this thread and one on Range Rovers.net I've confused myself as to what goes where so here's what I think it is. I've blown a cruise control fuse and stuffed the eco stop start with this so I don't want to do that again! Unless that was me and the multimeter trying to figure out what colour on that plug did what - should've just come here.
So here goes with the plug under the dash by our drivers right leg - grey plug/receptacle for the tekonsha/ford plug.
Blue on the Tow Pro goes to Blue on the Rangie - Easy
White on the Tow Pro (earth) goes to BLACK on the Rangie (black on the rangie at the plug under the drivers right leg is earth for this right??)
Red on the Tow Pro (brake lights) goes to Brown on the Rangie?
Black on the Tow Pro (power) goes to Green/Red on the Rangie?
If someone whom knows better can help me here I will be very grateful. I had a thread on this on the L405 group but this has been much more handy. I have even briefly toyed with putting the tow pro down the back and wiring it old school to the battery with a fuse of course, then to pin 5 on the trailer plug for blue, white earth to the chassis and red to the brake lights but if I can use that plug under the dash AND not lose cruise control (miss it when it ain't there!) that will save a whole lot of Cat 5 network cabling from the rear to the front.
If I can get this right I will repost the "answer" on the L405 thread I had. I am assuming of course the L494 wiring colours are the same as the L405 (they wouldn't do that to us would they??!!)
Cheers guys (and gals).
Darryl
The L494 wiring diagram shows that the brake light switch (trigger) wire is Violet/brown, not plain brown which is an unused tail-light supply. Your other colours match the L494 wiring diagram.
MY12 RRV 4.4 TDV8 AB, +LLAMS, +e-diff, +ACC stop/go. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
VK2HFG and APRS W1 digi
Ok awesome thanks Graeme. Will try tonight and advise.
Search AULRO.com ONLY! |
Search All the Web! |
---|
|
|
Bookmarks