Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: Birmabright. An interesting opinion & mainly based on fact??

  1. #11
    Join Date
    Nov 2008
    Location
    Bruthen, Eastern Vic.
    Posts
    836
    Total Downloaded
    0
    Quote Originally Posted by gromit View Post
    Apparently chosen because it was available as soft, 1/4 hard or 1/2 hard, also had excellent corrosion resistance.
    High tensile....yes but no pure aluminium both sides.

    Details here (if you believe Wikipedia) Birmabright - Wikipedia
    The details above mention that Birmetals made aircraft alloys.

    Some interesting old adverts here Birmetals - Graces Guide
    Posted earlier was this article on Birmabright including another 'story' on why it was chosen for Land Rovers Defender body panels are not Birmabright | FunRover - Land Rover blog & magazine


    Colin

    P.S. Just found this if you have the time to read it......Birmabright
    Thanks Colin, interesting read.
    Terry
    80 109" 2.6 P ex Army GS, saved from the scrappie.
    95 300tdi 130 Single cab tray.
    2010 Guzzi 750

  2. #12
    Join Date
    Jan 1970
    Location
    Narre Warren South
    Posts
    6,314
    Total Downloaded
    0
    Quote Originally Posted by RANDLOVER View Post
    I think I read that the DC100 Defender Concept was to have the body made out of plastic, which I think would have been great for polishing out scratches, even removing dents by heating with the wife's air dryer when she's not looking. This would've been like the modern successor to the old easily removable panels.
    I ran a Renault Espace II in the UK about 25 years ago. Galvanised monocoque chassis with GRP panels bonded on. Renault Espace - Wikipedia

    I think the Smart car was similar, plastic panels. Original concept was you could drive in, swap the panels and drive out with a new-look car (probably a Swatch idea).

    Could have worked on the new Defender.
    Rust free, dents pop out.
    Damage a panel and just buy a replacement and fit it (pretty much what a panel shop does nowadays).



    Colin
    '56 Series 1 with homemade welder
    '65 Series IIa Dormobile
    '70 SIIa GS
    '76 SIII 88" (Isuzu C240)
    '81 SIII FFR
    '95 Defender Tanami
    '58 Series II (sold)
    Motorcycles :-
    Vincent Rapide, Panther M100, Norton BIG4, Electra & Navigator, Matchless G80C

  3. #13
    JDNSW's Avatar
    JDNSW is online now RoverLord Silver Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    28,805
    Total Downloaded
    0
    The question as to whether the alloy panels on the first Landrovers were left over aircraft panels is a somewhat blurred one.

    The reason Rover even considered using anything except steel was simply because of the restrictions on their getting steel, which was rationed because of shortages. On the other hand, aluminium alloys were readily available, because the demand for these in aircraft manufacture dropped abruptly after VE-day as orders for new commbat aircraft in the UK were cancelled - the alloy for these was already in the pipeline.

    It has never been clear to me whether the sheet birmabrite used in Landrovers was material headed for these contracts, or whether it had been re-rolled or even realloyed to make it more suitable for civilian use. But despite this uncertainty, the alloy was certainly only available because of the cancellation of aircraft orders - for example, 150 Spitefuls were ordered, only 40 were built, no Furys were built, only a much smaller number of Sea Furys. And the Sunderland, which used a lot more alloy per aircraft "With the end of the war, large contracts for the Sunderland were cancelled " (Wikipedia). And there were far more contracts cancelled - these are just examples.

    Rover had experience in fabricating alloy aircraft assemblies during the war, and undoubtedly would have had contacts with the alloy suppliers.
    John

    JDNSW
    1986 110 County 3.9 diesel
    1970 2a 109 2.25 petrol

  4. #14
    Join Date
    Feb 2007
    Location
    Yass NSW
    Posts
    5,551
    Total Downloaded
    0
    When I was welding up holes on my series one a couple of years ago I used 5356 Alloy filler rods which worked pretty well with the TIG. 5356 has 5% magnesium in the alloy.

    Regards,
    Tote
    Go home, your igloo is on fire....
    2014 Chile Red L494 RRS Autobiography Supercharged
    MY2016 Aintree Green Defender 130 Cab Chassis
    1957 Series 1 107 ute - In pieces

    Assorted Falcons and Jeeps.....

  5. #15
    Join Date
    Sep 2013
    Location
    Darwin
    Posts
    1,632
    Total Downloaded
    0
    I thought birmabright was chosen because it work hardens when folded and therefore holds its form.

Page 2 of 2 FirstFirst 12

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!