Results 1 to 8 of 8

Thread: Haflinger Charging Light

  1. #1
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,474
    Total Downloaded
    0

    Haflinger Charging Light

    The charging system in my Haflinger is a generator system with an external voltage regulator.

    In my vehicle I have replaced the old (Series 1 LR style) voltage regulator with a Bosch electronic model. Normally when the engine is below 1200RPM the ignition light is on and above that it is off (all normal for these vehicles). Normally my voltage meter shows 13.8v when driving around.

    Recently I have noticed the voltage has been down as low as 11.5v when driving around with the lights on when normally with full electrical load it would be above 13v.

    When testing the battery at rest it was always between 12 and 12.5v and even with the engine running it was the same indicating it was not getting enough charge. At the generator it was pushing out 14.8v (normal) but only about 12.5v at the battery indicating either a dry joint between the regulator and the battery or a dud regulator.

    So I replaced the voltage regulator and all fixed - now back to 13.8v light load in the system so a faulty voltage regulator.

    So my question is - how come the charging light all worked as normal when clearly the system was not generating enough power to recharge the battery. Below the usual 1200 rpm the charging light was on, and over 1200rpm the light was off even though the battery was not being charged.

    Thanks

    Garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon

  2. #2
    Join Date
    Apr 2009
    Location
    Crafers West South Australia
    Posts
    11,732
    Total Downloaded
    0
    It depends on how the charge light is rigged, the indicator may be switched off by current flowing from the armature. The current may be insufficient to charge the battery under load but enough to turn off the light. It's been a while since I last worked on a genny.

  3. #3
    Join Date
    Jan 2008
    Location
    Nowra NSW
    Posts
    3,906
    Total Downloaded
    0
    Usually on a generater system the charging light is switched by the cut out contacts in the reguator............
    As mentioned..........the system was charging, and the light was showing that.
    Just it was not enough.

  4. #4
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,474
    Total Downloaded
    0
    Thanks for the comments - so in reality the charging light is only effective if the actual generator has failed rather than components further down the charging system which results in a lack of charge to the battery.

    I guess the same applies to the charging system in a series 1 Landrover.

    garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon

  5. #5
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    13,981
    Total Downloaded
    0
    For an electronic regulator, the charging light registers the difference in voltage between the alternator and battery.

    So when the ign is On , but engine not running the alternator is producing zero , but the battery is 12v , so the light is bright.
    If the light shines in a dull fashion after the engine is started , it means there is a voltage difference between the alternator and battery.
    This can be poor connections on the positive, inadequate gauge wiring, or poor earths.

    As a test you could use a jumper lead for starting to connect the alternator/regulator positive to the battery positive to see if the light changes , and do the same from the alternator body to the negative.
    Regards Philip A

  6. #6
    Join Date
    Sep 2018
    Location
    Thornleigh or Mt Marsden
    Posts
    34
    Total Downloaded
    0

    Might be only half a circuit

    Another possibility, the electronics may have only half failed. I've seen bridge rectifiers for instance with only half the bridge working. So the electronics supplying the lamp may have been OK but the parts (e.g. transistor or SCR) supplying the battery may have been so low in gain as to be ineffective.

  7. #7
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,474
    Total Downloaded
    0
    Quote Originally Posted by garrycol View Post
    The charging system in my Haflinger is a generator system with an external voltage regulator.

    In my vehicle I have replaced the old (Series 1 LR style) voltage regulator with a Bosch electronic model. Normally when the engine is below 1200RPM the ignition light is on and above that it is off (all normal for these vehicles). Normally my voltage meter shows 13.8v when driving around.

    Recently I have noticed the voltage has been down as low as 11.5v when driving around with the lights on when normally with full electrical load it would be above 13v.

    So I replaced the voltage regulator and all fixed - now back to 13.8v light load in the system so a faulty voltage regulator.
    So I replaced the Bosch electronic voltage regulator back on 14 Nov 18 and have only covered about 500km since. Drove tonight and voltage was up around 13.5v with the headlights on. Driving back home voltage is back down to 11.5v so it looks like the voltage regulator has failed again.

    Putting aside the obvious issue that I just got a dodgy voltage regulator, it there anything in a basic generator system (like is in a Series 1 LR) that can kill regulators?

    Thanks

    Garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon

  8. #8
    Join Date
    Jan 1970
    Location
    Kallangur, Brisbane
    Posts
    1,076
    Total Downloaded
    0
    Had spotties on mine so the dynastart copped a flogging when on high beam.

    Haflinger.JPG
    + 2016 D4 TDV6

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!