"How long since you've visited The Good Oil?"
'93 V8 Rossi
'97 to '07. sold.
'01 V8 D2
'06 to 10. written off.
'03 4.6 V8 HSE D2a with Tornado ECM
'10 to '21
'16.5 RRS SDV8
'21 to Infinity and Beyond!
1988 Isuzu Bus. V10 15L NA Diesel
Home is where you park it..
[IMG][/IMG]
Proper cars--
'92 Range Rover 3.8V8 ... 5spd manual
'85 Series II CX2500 GTi Turbo I :burnrubber:
'63 ID19 x 2 :wheelchair:
'72 DS21 ie 5spd pallas
Modern Junk:
'07 Poogoe 407 HDi 6spd manual :zzz:
'11 Poogoe RCZ HDI 6spd manual
Hi
A pair of 10" fans have an area of around 157 sq in, a single 18" fan has an area of around 250 sq in.
I believe that is the main reason you see mostly single fans these days
Steve
You have me interested now ... I just googled it ... Here's a picture of the falcon fans here.
Electric Fan Size
We are both wrong. It's radiator shape. If you have a "square" radiator, single will cover more of the core. If it's long an narrow ... twin smaller fans will cover more of the core.... Makes a lot of sense to me. You want whatever configuration will cover the majority of the core!
seeya,
Shane L.
Proper cars--
'92 Range Rover 3.8V8 ... 5spd manual
'85 Series II CX2500 GTi Turbo I :burnrubber:
'63 ID19 x 2 :wheelchair:
'72 DS21 ie 5spd pallas
Modern Junk:
'07 Poogoe 407 HDi 6spd manual :zzz:
'11 Poogoe RCZ HDI 6spd manual
Steve any idea what amperage the ba single fans draw?
Cheers Paul
I have one of these puppies (the BF one) and soon enough it’ll be in my P38 running both low and high speeds via temp controller. I plan to spend significant time in hot environments testing it and comparing to the viscous fan (pre and post testing).
Steve, do you know what effect running 12v to both the low and high speed wires at the same time would do? I have tested them both, and they do indeed operate slow and fast, I just don’t want to destroy the thermistor on the low speed side by running full speed at the same time.
Just trying to keep it simple, but making it work efficiently at the same time.
Ill remove the ford plug and use an Anderson plug instead, I can test current draw that way Paul.
Cheers
Keithy
Hi Mate
I finished up removing the BA fan as it seemed that under some conditions it just didn't move enough air to keep the engine cool, even with the Aussie Desert Cooler radiator fitted.
The single BA fan is the same diameter as the rover viscous fan, but is only about 2/3rd as deep, so it does not move the same amount of air sadly.
I finished up just running it on a single thermo switch, so either on or off. I never managed to work out the current draw either
90% of the time it was fine, but puling my Camper Trailer up a 5Km steep hill when leaving Gosford and being off road in low range I had to kill the air-con to keep the temperature down.
That said my air-con evaporator was in pretty poor shape so maybe the air-con load was higher then then it will be with the evaporator replaced
I'll be interested in your experience with the electric fans mate
Steve
Hi Steve,
The a/c fans really should be operated from a pressure switch in the a/c system. Their purpose is to stop the a/c pressure exceeding safe limits, This can happen really quickly if there is insufficient airflow over the condenser. By all means run a separate temp switch to bring them in if the engine temp increases, but don't rely on this alone to keep the pressure in the a/c system within safe limits.
Also be aware that a temp switch in the top of the radiator tank is only going to measure temperature accurately when in contact with the coolant. If the coolant level drops for some reason the sensor will not operate correctly.
Good luck
LuckyLes
Search AULRO.com ONLY! |
Search All the Web! |
---|
|
|
Bookmarks