Page 1 of 2 12 LastLast
Results 1 to 10 of 17

Thread: CAD for trailer canopy design

  1. 11th September 2012, 03:16 PM #1
    mattg Guest

    CAD for trailer canopy design

    Hi folks. Just bought this trailer its a beast. I need to cover the cage an build an extension out the front that follows the draw bar. For 2 reasons. extra dry storage and extra 2 inches so I can sleep in it. Have not decided to clad it with light Checker plate or gal sheet.

    I am after a simple cad program that I can use on the Mac to do the plans as I only want to do this once.

    Cheers Matt ImageUploadedByTapatalk1347344137.011753.jpg
    Reply With Quote Reply With Quote
  2. 11th September 2012, 03:46 PM #2
    Ranga's Avatar
    Ranga
    Ranga is offline Moderator
    Join Date
    Feb 2008
    Location
    Scarborough, QLD
    Posts
    3,315
    Total Downloaded
    0
    This might get you by Trimble SketchUp
    Reply With Quote Reply With Quote
  3. 11th September 2012, 05:59 PM #3
    TonyC
    TonyC is online now Wizard Silver Subscriber
    Join Date
    Sep 2007
    Location
    NE Victoria
    Posts
    1,413
    Total Downloaded
    32.83 MB
    Hi Matt,
    You could try Draft Sight, it's a freeware CAD that runs on Mac as well as Linux and Windows.

    Free CAD software * for your DWG files: DraftSight - Dassault Systèmes

    Tony
    Reply With Quote Reply With Quote
  4. 14th September 2012, 12:34 PM #4
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,770
    Total Downloaded
    1.13 MB
    What about cladding with ally sheet ?
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
  5. 17th September 2012, 06:26 AM #5
    mattg Guest
    I am looking ally sheet but I need wider then1200 wide. I haven't been into the steel joint yet but I would like to use checker plate. I also looked at gal sheet and then paint it but I have the same issue. I'll find my measurements.
    Reply With Quote Reply With Quote
  6. 17th September 2012, 08:31 AM #6
    mattg Guest
    The top is 1460x1870 and the back door is going to be 1430 x1460. They don't fit into a standard sheet.
    Reply With Quote Reply With Quote
  7. 17th September 2012, 07:06 PM #7
    Witchdoctor
    Witchdoctor is offline Master
    Join Date
    Dec 2011
    Location
    North Tambourine
    Posts
    716
    Total Downloaded
    0
    I used ally sheeting on my camper box, the roof section is 1950 x 1480 the joint is fully supported and the sheets are butted together. our camper has now done 40000 K's with no problems with that joint, if bonded properly.
    If you need any tips just PM me.
    Good luck

    David
    Reply With Quote Reply With Quote
  8. 17th September 2012, 08:39 PM #8
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,770
    Total Downloaded
    1.13 MB
    Even the thinest checkerplate will make the canopy too heavy.
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
  9. 18th September 2012, 05:42 AM #9
    mattg Guest
    Thanks guys what thickness ally sheet should I use? And Dave how did you attach to the frame and how did you dust seal it? Matt
    Reply With Quote Reply With Quote
  10. 18th September 2012, 07:01 AM #10
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,770
    Total Downloaded
    1.13 MB
    I think the gal sheet i was looking at is 0.9mm and ally around the same.
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
Page 1 of 2 12 LastLast
« Defender/Puma 2nd Battery | Sound insulation in Defender »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!