Barney - a 1958 Series II

Peter, if you want to bring it round to my place, we can figure it out using my multimeter.

Cheers,
John

Ta mate.

Probably Friday arvo. I'll give you a call...

Number plate holder.

My fabrication skills have improved a bit since I started watching “Project Binky” on YouTube.

https://photos.smugmug.com/Land-Rove...6_183757-L.jpg



Tailgate down position

https://photos.smugmug.com/Land-Rove...6_183931-L.jpg




A rare earth magnet will stop it from rattling

See? Here it is...

https://photos.smugmug.com/Land-Rove...6_184027-L.jpg



A neat solution for the lamp wire

https://photos.smugmug.com/Land-Rove...6_183850-L.jpg



You may have noticed a bit of an increase in production around here... yes, I’m batching again... 🤠

Hi Peter, nice work !!

Is there no gal piece at the top edge of the tail gate ?

Cheers,
John

Re the Horn Button assy. FWIW


The original surround for the button was " Black Cracker Laquer" finish (My name for it). Available in P/Pack tins. Could also be called Hammer finish. ? ? ? Was a sort of a rough to touch finish paint..

Remember the old Ned Kelly toy cap Guns or have you grown up with Ray or Laser guns? [biggrin] [bighmmm] Same finish.

You have done a really nice job on that vehicle, really nice..:TakeABow::TakeABow:

Forgot to mention.[bighmmm] If you wish for the Tailgate chains to not rattle, either slide a length of bike inner tube over each one or have made up a couple of PVC stitched tubes same as the seat material. Job done.

Quote:

---

Originally Posted by JohnboyLandy

Is there no gal piece at the top edge of the tail gate ?

Cheers,
John

---

There is. It's in the next pile to be galvanized

Quote:

---

Originally Posted by 4bee

Re the Horn Button assy. FWIW


The original surround for the button was " Black Cracker Laquer" finish (My name for it). Available in P/Pack tins. Could also be called Hammer finish. ? ? ? Was a sort of a rough to touch finish paint..

Remember the old Ned Kelly toy cap Guns or have you grown up with Ray or Laser guns? [biggrin] [bighmmm] Same finish.

You have done a really nice job on that vehicle, really nice..:TakeABow::TakeABow:

Forgot to mention.[bighmmm] If you wish for the Tailgate chains to not rattle, either slide a length of bike inner tube over each one or have made up a couple of PVC stitched tubes same as the seat material. Job done.

---

Thank you, I appreciate your comments.
I have the PVC chain sleeves, but first I have to get new chain, one is half a link longer than the other, which is annoying me. Means the tailgate only rests on one side until you push the other side down, and then it's crooked. [bigsad]

Check that the chains are actually different lengths and it is not that the position of the anchors are slightly different.

Quote:

---

Originally Posted by JDNSW

Check that the chains are actually different lengths and it is not that the position of the anchors are slightly different.

---

Check if the chains twisted too. That can make them shorter as well.

Quote:

---

Originally Posted by 4bee

Re the Horn Button assy. FWIW


The original surround for the button was " Black Cracker Laquer" finish (My name for it). Available in P/Pack tins. Could also be called Hammer finish. ? ? ? Was a sort of a rough to touch finish paint..

.

---

I think it was called wrinkle finish (probably other terms for it).
Dupli-Color Wrinkle Aerosol Paint - Wrinkle Finish, Black, 312g | Supercheap Auto

http://www.2040-parts.com/_content/i...218383/001.jpg


Colin

That is it, Colin, Ned Kelly Black, but it was about 20 odd years ago when I bought my can, hence me renaming it..[smilebigeye]


Just had another look at mine before I just came in & I reckon I must have nicked your one.[biggrin]

Gave me an excuse to press/test the horn button & I must say, LR did select a great horn for these.

No, it didn't play Jingle Bell Rock or the French National Anthem either.