Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 25

Thread: Series IIa Motor Rebuild.

  1. 4th September 2019, 04:17 PM #11
    Ferg's Avatar
    Ferg
    Ferg is offline Fossicker Gold Subscriber
    Join Date
    Dec 2010
    Location
    Newcastle, NSW
    Posts
    29
    Total Downloaded
    0
    Yup, advanced the timing to between 8 & 9 deg. Hard to tell with no definitive marks. The model number would be great thanks.
    Quote Originally Posted by Phil B View Post
    Single barrel.
    I値l get you the model number if you like.
    It did tend to run a little lean out of the box but that was easily fixed with the next size up main jet.
    Been running for 3 yrs now with zero adjustment.
    Have you advanced the timing?
    Reply With Quote Reply With Quote
  2. 4th September 2019, 04:27 PM #12
    Phil B
    Phil B is offline Wizard Subscriber
    Join Date
    Feb 2014
    Location
    Sydney
    Posts
    1,073
    Total Downloaded
    0
    Ok
    I値l find it st the weekend
    Phil B

    Custodian of:
    1974 S3 swb wagon (sold)
    1978 S3 swb canvas
    48 749 '88 4x4 Perentie
    1985 County with 4BD1T
    Reply With Quote Reply With Quote
  3. 4th September 2019, 04:29 PM #13
    Phil B
    Phil B is offline Wizard Subscriber
    Join Date
    Feb 2014
    Location
    Sydney
    Posts
    1,073
    Total Downloaded
    0
    Quote Originally Posted by B.S.F. View Post
    How many miles /kms and under what conditions ?
    .W.
    It痴 on heritage plates so maybe 5000km? Not sure exactly.
    Mainly road with a few easy tracks.
    Phil B

    Custodian of:
    1974 S3 swb wagon (sold)
    1978 S3 swb canvas
    48 749 '88 4x4 Perentie
    1985 County with 4BD1T
    Reply With Quote Reply With Quote
  4. 7th September 2019, 11:14 AM #14
    Phil B
    Phil B is offline Wizard Subscriber
    Join Date
    Feb 2014
    Location
    Sydney
    Posts
    1,073
    Total Downloaded
    0
    Quote Originally Posted by Phil B View Post
    Ok
    I値l find it st the weekend
    This is the kit I have on my 2.25 p S3
    Hope this helps
    Phil B

    Custodian of:
    1974 S3 swb wagon (sold)
    1978 S3 swb canvas
    48 749 '88 4x4 Perentie
    1985 County with 4BD1T
    Reply With Quote Reply With Quote
  5. 7th September 2019, 11:16 AM #15
    Phil B
    Phil B is offline Wizard Subscriber
    Join Date
    Feb 2014
    Location
    Sydney
    Posts
    1,073
    Total Downloaded
    0
    Not sure if the photo attached so I値l try sgain
    Phil B

    Custodian of:
    1974 S3 swb wagon (sold)
    1978 S3 swb canvas
    48 749 '88 4x4 Perentie
    1985 County with 4BD1T
    Reply With Quote Reply With Quote
  6. 7th September 2019, 02:58 PM #16
    Xtreme's Avatar
    Xtreme
    Xtreme is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Normanhurst, NSW
    Posts
    10,176
    Total Downloaded
    0
    Quote Originally Posted by goingbush View Post
    ........................ go for a drive , if it pings back it off a little, If it does not ping under load advance it some more. ........................
    This is how I used to time my Series IIA/III's and found that it was best to use 3rd gear under load to check for pinging.
    Reply With Quote Reply With Quote
  7. 7th September 2019, 03:12 PM #17
    Ferg's Avatar
    Ferg
    Ferg is offline Fossicker Gold Subscriber
    Join Date
    Dec 2010
    Location
    Newcastle, NSW
    Posts
    29
    Total Downloaded
    0
    Looks like the 341CH. Thanks for that. Paddocks stock them so I'll get straight onto it.
    Quote Originally Posted by Phil B View Post
    Not sure if the photo attached so I値l try sgain
    Reply With Quote Reply With Quote
  8. 7th September 2019, 03:14 PM #18
    Ferg's Avatar
    Ferg
    Ferg is offline Fossicker Gold Subscriber
    Join Date
    Dec 2010
    Location
    Newcastle, NSW
    Posts
    29
    Total Downloaded
    0
    I couldn't even get it in 2nd gear under load without it loading up. It's okay down my street but around the corner and up a very slight slope it dies in the arse. Nothing else left to replace after the carby.
    Quote Originally Posted by Xtreme View Post
    This is how I used to time my Series IIA/III's and found that it was best to use 3rd gear under load to check for pinging.
    Reply With Quote Reply With Quote
  9. 8th September 2019, 06:50 AM #19
    Phil B
    Phil B is offline Wizard Subscriber
    Join Date
    Feb 2014
    Location
    Sydney
    Posts
    1,073
    Total Downloaded
    0
    Have you checked your valve timing?
    Phil B

    Custodian of:
    1974 S3 swb wagon (sold)
    1978 S3 swb canvas
    48 749 '88 4x4 Perentie
    1985 County with 4BD1T
    Reply With Quote Reply With Quote
  10. 8th September 2019, 08:09 AM #20
    Ferg's Avatar
    Ferg
    Ferg is offline Fossicker Gold Subscriber
    Join Date
    Dec 2010
    Location
    Newcastle, NSW
    Posts
    29
    Total Downloaded
    0
    Yes, that was part of the checks I did with the engine builder to ensure the engineering was correct and the issue lay elsewhere.
    Quote Originally Posted by Phil B View Post
    Have you checked your valve timing?
    Reply With Quote Reply With Quote
Page 2 of 3 FirstFirst 123 LastLast
« SII Zenith (copy) Carb question | Engine rebuild, torqued down crankshaft won稚 move »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!