Printable View
I think the liquid steel is a KBS product? Haven't had much luck locating it here in Perth, (although I haven't looked that hard). I'll put these aside for spares, and to trial the method you've listed, (in the long term). I do have new non blue box ones to go on the car.Quote:
Originally Posted by chazza
I've had to resort to blue box parts for a couple of pieces as there was nothing else available, but they're more cosmetic parts, other than rotating, sealing, or machined parts.
Cheers,
What is "Blue Box"?
The dreaded Britpart....................... rightly or wrongly.Quote:
Originally Posted by OneOff
Cheers,
I have to say that I'm enjoying this thread and to answer the question by Landyandy, mate you just have to make time LOL, I'm now sorta semi-retired I have a wife n 6 x 4 legged dependants, 7 bantams, and fish in ponds LOL, but you just have to swing it between all manner of things and a shed full of stuff 2 metal lathes a mill/drill and other stuff including this
https://www.aulro.com/afvb/images/im...016/12/451.jpg
and from another perspective
https://www.aulro.com/afvb/images/im...016/12/452.jpg
you just have to make time out of nothing LOL but I must admit I don't have any kids living at home well I'm almost 68 LOL cheers Dennis
ps TimNZ sorry for the slight off topic hi-jack,,.
Quote:
Originally Posted by chazza
Yep! And "Blue Box" or should that be "Blue Bag" radiator hoses perish about six months after fitting. Mind you they sat in the shed for about six months before fitment! :(
Bloody annoying to say the least!!!
Cheers, Mick.
Got started on the binnacle whilst sat down in front of the idiot box tonight. Aside from generally schmoo around the clocks, the panel light switch is frozen solid, and the high beam lens of the speedo is broken off.
https://www.aulro.com/afvb/images/im...016/12/462.jpg
A spare speedo was aquired, I decided to rob the high beam lens of this and repair my original one as the spare had a different code on the sticker inside, (I assume it has a different ratio and is off a 109), and the clock face on the original is in slightly better nick.
The bezel looks like it should rotate and then come off, (there are little tabs on the bezel that line up with cut outs on the housing), however I had to pry the tabs up to release it due to the corrosion/goo/sealant holding it on. I have replacement glass and bezels on the way which should be here soon.
https://www.aulro.com/afvb/images/im...016/12/463.jpg
Original Jaeger gauge on the left, older, (I think), Smiths on the right. The "Smiths" name is blacked out for some reason.
https://www.aulro.com/afvb/images/im...016/12/464.jpg
The lenses are held in with a conical washer, which was carefully prised off.
https://www.aulro.com/afvb/images/im...016/12/465.jpg
Speedo with the replacement lens fitted, and clock face cleaned gently with some glass cleaner, cotton buds, and the micro fibre cloth stolen from my camera bag :angel:
https://www.aulro.com/afvb/images/im...016/12/466.jpg
Inner bezel also needed cleaning
https://www.aulro.com/afvb/images/im...016/12/467.jpg
https://www.aulro.com/afvb/images/im...016/12/468.jpg
The Jaeger housing (left) has a light blue backing around the top, whilst the Smiths is completely white. I'm not sure what effect the blue is supposed to give? Maybe make the yellowish back light appear more white?
https://www.aulro.com/afvb/images/im...016/12/469.jpg
All back together, just need to wait for the new lens and bezel, oh and repeat this process on the other clock!
https://www.aulro.com/afvb/images/im...016/12/470.jpg
Gave the binnacle a good clean also. I used Meguiars interior cleaner, a soft brush, microfibre cloth, and plenty of warm water. Pretty happy with how it came up
https://www.aulro.com/afvb/images/im...016/12/471.jpg
Cheers,
Nice work there Tim. I've got to do the instruments on mine too to clean out several years of Pilbara dust. I have given some plastic parts like your binnacle a quick coat with a satin black spray can and they come up great too.
THAT IS AWESOME Dennis.Quote:
Originally Posted by Dinty
Steam has always interested me.I love looking at old steam locos and farm machinery.That scale model is loverly.
ENJOY
Andrew
Went to pick the replacement outriggers today, but unfortunately they're not finished :( They should be done next week, but I won't get the chance to fit them till after Christmas.
Anyway, got on to the last spring mount this evening. For as long as anyone can remember the Landy has had a list to starboard, and when I was trying to line up the threaded rod I think I've found out why. The distance from the spring bolt, (where the threaded rod is), is at least half an inch closer to the chassis on the drivers side.
I levelled the chassis as best I could, by checking the level at various points down the chassis, (it was actually pretty close at all the places I measured). It's a bit hard to see the bubble in the level in the picture, but it's all the way over to the right.
(Yes, I know I'm probably being a bit picky using a level thats graduations measure 0.42mm per meter, given that 70's BL used tolerances to the closest inch)
https://www.aulro.com/afvb/images/im...016/12/441.jpg
A short bit of surgery with the die grinder, and the level was much better:
https://www.aulro.com/afvb/images/im...016/12/442.jpg
New "washers" were cut out of some 6mm plate:
https://www.aulro.com/afvb/images/im...016/12/443.jpg
But the holes needed to be moved off center, so the holes from the hole saw drill needed to be filled in first:
https://www.aulro.com/afvb/images/im...016/12/444.jpg
Then they could be redrilled and welded on. (The distance between the rear most mount and threaded rod was checked to be equal on both sides)
https://www.aulro.com/afvb/images/im...016/12/445.jpg
I still need to fill in the wear on the rest of the chassis mount, but that can wait till tomorrow.
The other "5 minute job" I tackled was to remove this broken bolt in the outer swivel housing, easy right....
https://www.aulro.com/afvb/images/im...016/12/446.jpg
I tried drilling it first, turns out it's a BSF bolt (1/4"), and a high tensile one at that. I started with a 3mm cobalt drill bit, may as well used a piece of wooden dowel.
So.... plasma cutter?
https://www.aulro.com/afvb/images/im...016/12/447.jpg
Worked surprisingly well
https://www.aulro.com/afvb/images/im...016/12/448.jpg
The hole was then drilled out with a 5mm bit, which sacrificed it's life by doing so, given how hard the material was. I didn't fancy the little 1/4" BSF tap's chances of cutting away the rest of the high tensile bolt, so the gas torch was broken out, the remains of the bolt heated, then allowed to cool. This made it soft enough to tap out the hole:
https://www.aulro.com/afvb/images/im...016/12/449.jpg
And... all done:
https://www.aulro.com/afvb/images/im...016/12/450.jpg
Cheers,
Started sorting through the nuts, bolts and other bits of the front axle today. Got all the bolts organised for which ones need cleaning, and any brackets that need blasting and painting set aside.
https://www.aulro.com/afvb/images/im...016/12/400.jpg
If in doubt, gas axe?
https://www.aulro.com/afvb/images/im...016/12/401.jpg
Whilst things were waiting for their paint to dry, and various bolts were soaking in degreaser I started on the front diff. Which is actually the rear diff, because the new rear diff, the old front diff, is getting an upgrade, and going in the back because it has less wear than the rear diff. Also the front diff, which is the old rear diff, is getting the center from the spare diff as it is in better nick. Confused? Good, I am to.
New pinion bearing shells getting pressed in
https://www.aulro.com/afvb/images/im...016/12/402.jpg
https://www.aulro.com/afvb/images/im...016/12/403.jpg
The donor diff center got stripped and cleaned. Little bit of wear on the cross pin, but not bad enough to warrant changing:
https://www.aulro.com/afvb/images/im...016/12/404.jpg
Little bit of wear to the housing, but the sun/planet gears were still quite tight:
https://www.aulro.com/afvb/images/im...016/12/405.jpg
All the bits cleaned and ready for reassembly
https://www.aulro.com/afvb/images/im...016/12/406.jpg
Bearings getting pressed on:
https://www.aulro.com/afvb/images/im...016/12/407.jpg
3 diffs worth of crown wheel bolts. The bolts on the front diff were also only finger tight, I think both diffs were done up with a "grunt twice" type torque wrench. As you can see quite a few of the bolts are stretched or damaged. All the bolts from the donor diff were fine.
https://www.aulro.com/afvb/images/im...016/12/408.jpg
Crown wheel getting refitted, with an actual torque wrench.
https://www.aulro.com/afvb/images/im...016/12/409.jpg
All done, lock tabs, (and loctite for good measure :angel: )
https://www.aulro.com/afvb/images/im...016/12/410.jpg
Modified the old pinion bearing into a pressing sleeve:
https://www.aulro.com/afvb/images/im...016/12/411.jpg
https://www.aulro.com/afvb/images/im...016/12/412.jpg
Diff going back together, checking the run out, (was 0.03mm)
https://www.aulro.com/afvb/images/im...016/12/413.jpg
And back lash
https://www.aulro.com/afvb/images/im...016/12/414.jpg
Tooth pattern on the coast side is OK
https://www.aulro.com/afvb/images/im...016/12/415.jpg
But to get an even contact on the drive side the back lash is way out to 0.4mm, and the contact is right in by the root of the teeth. I think I'll have to thin the pinion shimming down :(
I've put a thread about this in the technical section to get some advice.
https://www.aulro.com/afvb/images/im...016/12/416.jpg
And finally, more painting, yay.... Some of the new parts, (spring U bolts, swivel seal retainer etc), had the goldish anodising, that for one I don't really like, and two, is only good for preventing corrosion while parts are in storage. So they got a quick sandblast to provide a key for the paint, then some etch primer, (the KBS stuff).
https://www.aulro.com/afvb/images/im...016/12/417.jpg
Cheers,