Matilda's getting an engine rebuild!

Quote:

---

Originally Posted by wrinklearthur

no edit function this thread, so did again.
.

---

So all I need is 219466 (bearing) and 278025 (shaft)? Are these from Craddocks?

(Sorry for my ignorance).

Hi Scallops,

We have found the best condensor's to be Bosch GL98-C. Application details on the back say for Plymouth 53, Sunbeam 53-55 & Vauxhall 53 Velox. They are a bit of a pain to install as they don't have a captive bracket, but with a little patience go on a treat. They really do seem to last well though. I had a brand new old stock 1951 correct PN condensor from the UK & it failed after less than 1000kms. The Bosch condensor is available from an Cov's (Coventry's) over in the west.

Cheers

Here is a series 1 spare parts manual, look at page 84.

http://www.landroverseries.org/LRS1/...20COMPLETE.pdf
.

Cross reference with the parts list I have from 4WD Melbourne and I get:

T42B B on (Pair) and Series III . . . . . . . . . . . . . . . . . . . .$ 19.80ea.
T43 Bearings (Pair) up to A . . . . . . . . . . . . . . . . . . . . . .$ 35.20ea.
T43B B on (Pair) and Series III . . . . . . . . . . . . . . . . . . . .$ 29.70ea.
T44 Intermediate Gear to A . . . . . . . . . . . . . . . . . . . . .$165.00ea.
T44B B only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$165.00ea.
T44C C on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .$165.00ea.
T45 Intermediate Shaft to A (Diameter 1 1/8”) . . . . . . .$ 55.00ea.
T45B B on (Diameter 1 5/8”) and Series III . . . . . . . . . .$ 71.50ea.

IF they still have them in stock

Thank for the parts manual! Ok - so now I have the 2 part numbers for the shaft and bearing. Hopefully I'll be able to find these somewhere.

Quote:

---

Originally Posted by Scallops

So all I need is 219466 (bearing) and 278025 (shaft)? Are these from Craddocks?

(Sorry for my ignorance).

---

I would fit the correct amount of thrust washers and shims as well as they stop the noise that comes from the slop or end float on the intermediate gear. you can cut your own from shim brass if your are stuck.

Try again for a work shop manual description, this for a series 3 but is good enough to follow. look at page 37-13

http://www.landroverweb.com/Pdf-file...III_Part_4.pdf
.

There is also a gearbox manual from my Series 1 files here:

http://kiwi-in-oz.com/manuals/series1/Gearbox.pdf

Quote:

---

Originally Posted by drifter

There is also a gearbox manual from my Series 1 files here:

http://kiwi-in-oz.com/manuals/series1/Gearbox.pdf

---

Hi Drifter

Sorry, but I have already looked at that one and section C26 that covers the transfer box isn't there.

.

damn, the other one I have for older vehicles is this:

http://kiwi-in-oz.com/manuals/series...rbox_index.pdf

Page 39-C in the gearbox section maybe

So have you got a target for getting this finished Dan? Or just "no rush, it's done when it's done"?