Page 1 of 3 123 LastLast
Results 1 to 10 of 22

Thread: Name that tool

  1. 14th August 2006, 08:33 AM #1
    Ace's Avatar
    Ace
    Ace is offline Swaggie Gold Subscriber
    Join Date
    Jan 1970
    Location
    Bathurst NSW
    Posts
    14,445
    Total Downloaded
    0

    Name that tool

    Hi guys went to sydney on the weekend and the stop start traffic work finished off the rubber flange on the tail shaft, i have the gear to swap it over but was wondering if someone could tell me the name of the tool used to pull the shaft locating pin out of the centre of the pinion flange so i can get to the nut, i know slunnie used one to get his out but i am stuffed i know the name and all the tool suppliers dont have a bloody clue. Its different to a normal puller so if someone could give me a name to work with that would be good. Matt
    <a href=https://the4wdzone.com.au/wp-content/uploads/logo.png target=_blank>https://the4wdzone.com.au/wp-content/uploads/logo.png</a>
    The 4wd Zone/Opposite Lock Bathurst
    263 Stewart Street, Bathurst, NSW
    http://www.the4wdzone.com.au/
    Discounts for AULRO members, just shoot me a PM before you purchase.
    Reply With Quote Reply With Quote
  2. 14th August 2006, 09:46 AM #2
    walker's Avatar
    walker
    walker is offline Wizard
    Join Date
    Jan 1970
    Location
    Melbourne
    Posts
    1,937
    Total Downloaded
    0
    Pin Puller!
    Reply With Quote Reply With Quote
  3. 14th August 2006, 09:55 AM #3
    Ace's Avatar
    Ace
    Ace is offline Swaggie Gold Subscriber
    Join Date
    Jan 1970
    Location
    Bathurst NSW
    Posts
    14,445
    Total Downloaded
    0
    Quote Originally Posted by walker
    Pin Puller!
    Pin puller, thanks walker. They had a catalogue of all the different types of pullers at repco but they were all pully pullers. Matt
    <a href=https://the4wdzone.com.au/wp-content/uploads/logo.png target=_blank>https://the4wdzone.com.au/wp-content/uploads/logo.png</a>
    The 4wd Zone/Opposite Lock Bathurst
    263 Stewart Street, Bathurst, NSW
    http://www.the4wdzone.com.au/
    Discounts for AULRO members, just shoot me a PM before you purchase.
    Reply With Quote Reply With Quote
  4. 14th August 2006, 09:56 AM #4
    walker's Avatar
    walker
    walker is offline Wizard
    Join Date
    Jan 1970
    Location
    Melbourne
    Posts
    1,937
    Total Downloaded
    0
    Ok, ok.

    How about this - LRT 51-008 service tool
    Reply With Quote Reply With Quote
  5. 14th August 2006, 10:11 AM #5
    4bee's Avatar
    4bee
    4bee is offline Cynical Moi?
    Join Date
    Jan 1970
    Location
    Adelaide Hills. South Australia
    Posts
    13,349
    Total Downloaded
    0
    Slide hammer?
    Reply With Quote Reply With Quote
  6. 14th August 2006, 01:05 PM #6
    british4wd Guest
    You do not need the puller to replace the rubber coupling, it is only needed when changing the diff pinion seal.
    Alan Howard
    Reply With Quote Reply With Quote
  7. 18th August 2006, 08:40 AM #7
    Ace's Avatar
    Ace
    Ace is offline Swaggie Gold Subscriber
    Join Date
    Jan 1970
    Location
    Bathurst NSW
    Posts
    14,445
    Total Downloaded
    0
    Quote Originally Posted by british4wd
    You do not need the puller to replace the rubber coupling, it is only needed when changing the diff pinion seal.
    Alan Howard
    I am not replacing the rubber coupling Alan i need to remove the pinion so i can put a 4 bolt pinion flange on to eliminate the rubber tool. Matt
    <a href=https://the4wdzone.com.au/wp-content/uploads/logo.png target=_blank>https://the4wdzone.com.au/wp-content/uploads/logo.png</a>
    The 4wd Zone/Opposite Lock Bathurst
    263 Stewart Street, Bathurst, NSW
    http://www.the4wdzone.com.au/
    Discounts for AULRO members, just shoot me a PM before you purchase.
    Reply With Quote Reply With Quote
  8. 18th August 2006, 08:49 AM #8
    RobHay's Avatar
    RobHay
    RobHay is offline ChatterBox
    Join Date
    Jan 1970
    Location
    Caboolture.Qld
    Posts
    2,382
    Total Downloaded
    0
    Personally I love my club Hammer and cold chisel, gets all tight little suckers off.
    Reply With Quote Reply With Quote
  9. 18th August 2006, 08:56 AM #9
    Ace's Avatar
    Ace
    Ace is offline Swaggie Gold Subscriber
    Join Date
    Jan 1970
    Location
    Bathurst NSW
    Posts
    14,445
    Total Downloaded
    0
    Well i have two options, buggerise around trying to get the tool or i can cut around the edges of it like Slunnie did splay it out with a cold chizel and then try and get it out that way.

    Anyone know where i can get the tool from, and how much it is, that might help me make up my mind. Matt
    <a href=https://the4wdzone.com.au/wp-content/uploads/logo.png target=_blank>https://the4wdzone.com.au/wp-content/uploads/logo.png</a>
    The 4wd Zone/Opposite Lock Bathurst
    263 Stewart Street, Bathurst, NSW
    http://www.the4wdzone.com.au/
    Discounts for AULRO members, just shoot me a PM before you purchase.
    Reply With Quote Reply With Quote
  10. 18th August 2006, 08:59 AM #10
    dobbo's Avatar
    dobbo
    dobbo is offline OldBushie
    Join Date
    Jan 1970
    Location
    Close enough to their Shire to smell the dirty Hobbit feet
    Posts
    8,059
    Total Downloaded
    0
    I don't know of where to get the tool.

    I just saw


    Name that tool
    ACE

    And had a little chuckle to myself
    Have you tried

    all four x 4 spares
    Reply With Quote Reply With Quote
Page 1 of 3 123 LastLast
« Disco 1 Tailgate | Good tyre prices in Melb ? »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!