Page 3 of 3 FirstFirst 123
Results 21 to 24 of 24

Thread: Do I Or Dont I..should I Or Shouldnt I.

  1. #21
    Join Date
    Oct 2003
    Location
    Godwin Beach Qld
    Posts
    8,688
    Total Downloaded
    0
    G'day Banjo

    First up, was your Landy originally a 4 or a 6 if it was a 4 I would advise you to return to the 4, if it was a 6 you could replace your Holden motor quite easily, it would just mean removal of the Holden and replace with the 6, make sure that you get the 6 cyl engine mountings with the $100 motor, if this is the same motor from the car to start with ask why it was removed to start with as it may have had a valve or head gasket problem, it could also be that someone told him that the 6 was crap "Put a Holden in it Mate!" and he has ditched a good 6 cyl for a revving Holden the Holden is a short stroke motor and needs reves to get torque, the Landrover motors (4's and 6's) are long stroke, and max torque comes on at very low revs, 1900--2500 rpm, and all have heavy flywheels,so that they are good at off road use, on highway they are slow off the mark but will run at between 80--100 Kph on a light throttle, as the flywheel enertia holds the revs. to improve the braking fit 6cylinder model front brakes 3 inch wide shoes and a booster, as that was what was used until discs on the V8 110's and they stopped OK. The steering should not be heavy if set up correctly, I have no trouble driving my 2a 4cyl at highway speeds using one hand and resting my elbow on the door, and parking is not a problem, BUT it is heavier with Radials than with Conventionals, with Radials set the steering at Zero Toe In

    The 6cyl motor does need regular tappett adjustment (5,000klms)


    REMEMBER: these vehicles are NOT Commodores,Falcons, or WRX's and accelerate like them

    cheers

  2. #22
    Join Date
    Jun 2003
    Location
    Launceston, Tasmania
    Posts
    12,347
    Total Downloaded
    0
    all this talk of 6 cyl rovers is depressing me. I want one in mine

    I must call the bloke who was going to swap me and see how he is
    1994 Discovery TDi
    2004 Discovery 2 TD5
    2010 Discovery 4 TDV6
    1961, Series 2 Ambulance. 108-098 - Eden

    Registry of Ex Military Land Rovers Mem. 129
    Defence Transport Heritage Tasmania Member

  3. #23
    Join Date
    Aug 2006
    Location
    WA
    Posts
    13,786
    Total Downloaded
    0
    Quote Originally Posted by banjo View Post
    i am also going to do the same as isuzurover has to his springs ,that thing of his is awesome...
    Thanks mate - at the moment the IIA is still 4500km from me, and needs a seal replaced in the injector pump... But I am hatching plans to drive it from Brisbane-Perth later in the year!!!

    Let me know if you need any help/advice when it comes to the springs. Whereabouts are you?

    Jimmy - the 2.25D is a good motor, if you look after it and you aren't in a hurry to get where you are going. That said, with a bit of tinkering they can perform better than a 2.25P.

    The conversion is simple and basically bolt-in. If you are converting a 6cyl though you may have to swap the chassis mounts and bellhousing to 4cyl type.

  4. #24
    Join Date
    Feb 2007
    Posts
    205
    Total Downloaded
    0
    Keep in mind Banjo did say he couldn't afford to put in a TDi engine.

    So working on that and the fact it already has the holden motor, it would seem more common sense to work on what he already has. He could easily throw some money at the Landie towards other improvements to make it a good (better) vehicle.

    If money is short I see no point in re-inventing the wheel by pulling out an existing engine to replace it with something that won't improve it that much if any depending on his choice.

    Best regards
    DarrenR

Page 3 of 3 FirstFirst 123

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!