Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: 300 TDi Defender - Replacing the Bonnet Support

  1. 4th June 2007, 07:28 AM #11
    JDNSW's Avatar
    JDNSW
    JDNSW is online now RoverLord Silver Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    29,515
    Total Downloaded
    0
    Quote Originally Posted by Stephen Price View Post
    I had a look at mine and can see an advantage in that you could put in a longer rod so your bonnet will open further without having to stuff around pulling pins out and tying back. I might give it a go!
    I long ago replaced the split pin in mine with an R-clip!

    John Denham
    John

    JDNSW
    1986 110 County 3.9 diesel
    1970 2a 109 2.25 petrol
    Reply With Quote Reply With Quote
  2. 4th June 2007, 02:48 PM #12
    rangieman's Avatar
    rangieman
    rangieman is offline Swaggie
    Join Date
    Jan 1970
    Location
    Free Again Thanks Dan
    Posts
    10,150
    Total Downloaded
    0
    Quote Originally Posted by JDNSW View Post
    I long ago replaced the split pin in mine with an R-clip!

    John Denham
    ^^^^^^^^^^^ Replaced mine when i first got it a with a R clip
    Reply With Quote Reply With Quote
  3. 4th June 2007, 03:48 PM #13
    isuzurover's Avatar
    isuzurover
    isuzurover is offline Swaggie
    Join Date
    Aug 2006
    Location
    WA
    Posts
    13,786
    Total Downloaded
    0
    Quote Originally Posted by JDNSW View Post
    I have no problems with the scissor type stay - never would have thought of converting it.

    John
    Me too. Owned a v8 county briefly with a rod - no big advantage IME.

    If I was going to change it I would fit a gas strut instead.
    Reply With Quote Reply With Quote
  4. 1st September 2009, 04:29 PM #14
    VladTepes's Avatar
    VladTepes
    VladTepes is offline Major Part of the Heart and Soul of AULRO Subscriber
    Join Date
    Feb 2004
    Location
    Bracken Ridge, Qld
    Posts
    16,055
    Total Downloaded
    0
    Quote Originally Posted by isuzu110 View Post
    Scissor stay gets stuck under the fill point on the top airconditioner pipe when opening. You have to reach under with your left hand and pull the scissor to the left whilst lifting with the right hand. I suspect the top aircon pipe is non standard. Surely LR would not have had such a bad design.

    If you are not careful, you could snap the fill-point off.
    Almost exactly what happened to mine. The air con pipe has gouges in it, so I needed to get that scissor stay off before I needed a re-gas !

    Now to replace it...

    and why not a genuine LR one ?

    $100 - that's why !
    It's not broken. It's "Carbon Neutral".


    gone

    1993 Defender 110 ute "Doris"
    1994 Range Rover Vogue LSE "The Luxo-Barge"
    1994 Defender 130 HCPU "Rolly"
    1996 Discovery 1

    current

    1995 Defender 130 HCPU and Suzuki GSX1400

    Reply With Quote Reply With Quote
  5. 1st September 2009, 04:31 PM #15
    VladTepes's Avatar
    VladTepes
    VladTepes is offline Major Part of the Heart and Soul of AULRO Subscriber
    Join Date
    Feb 2004
    Location
    Bracken Ridge, Qld
    Posts
    16,055
    Total Downloaded
    0
    Oh and what on earth is an "R" clip ?
    It's not broken. It's "Carbon Neutral".


    gone

    1993 Defender 110 ute "Doris"
    1994 Range Rover Vogue LSE "The Luxo-Barge"
    1994 Defender 130 HCPU "Rolly"
    1996 Discovery 1

    current

    1995 Defender 130 HCPU and Suzuki GSX1400

    Reply With Quote Reply With Quote
  6. 1st September 2009, 04:49 PM #16
    Ranga's Avatar
    Ranga
    Ranga is offline Moderator
    Join Date
    Feb 2008
    Location
    Scarborough, QLD
    Posts
    3,315
    Total Downloaded
    0
    Quote Originally Posted by VladTepes View Post
    Oh and what on earth is an "R" clip ?
    Reply With Quote Reply With Quote
  7. 2nd September 2009, 02:55 PM #17
    VladTepes's Avatar
    VladTepes
    VladTepes is offline Major Part of the Heart and Soul of AULRO Subscriber
    Join Date
    Feb 2004
    Location
    Bracken Ridge, Qld
    Posts
    16,055
    Total Downloaded
    0
    Aaaaaaaaaaaaaaaaaarrrrrrrrrrrrrrrrrr I see !

    (It's a pirate thing!)
    It's not broken. It's "Carbon Neutral".


    gone

    1993 Defender 110 ute "Doris"
    1994 Range Rover Vogue LSE "The Luxo-Barge"
    1994 Defender 130 HCPU "Rolly"
    1996 Discovery 1

    current

    1995 Defender 130 HCPU and Suzuki GSX1400

    Reply With Quote Reply With Quote
  8. 21st October 2011, 11:32 AM #18
    rainman's Avatar
    rainman
    rainman is offline Master
    Join Date
    Jan 2009
    Location
    Samford
    Posts
    704
    Total Downloaded
    0
    Resurrecting an old thread here, but no one has mentioned a bonnet stay problem I had with both of my Defender Tdi's.

    The scissor type bonnet stay, whilst very practical to use, rubs on the top of the boost compensator in the injector pump. Not only is it noisy, it was actually wearing quite a bit off the housing. Does anyone else have rub marks on their injector pump?

    I've just been reading through a few threads and it seems a few have converted to the rod type stay as I am planning to do (been running without one and using a broom handle for 10 years ). It's an easy job using aluminium or steel.


    James.
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« 40,000km sevice costs | Land Rover Servicing Brisbane Area »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!