To rebuild or replace with a V8?

Quote:

---

Originally Posted by Ace

at the moment thats what is stopping me. But i cant ring Marks Adaptors to ask them what is needed, and how easy it is to hook up heating and cooling systems, radiator fans etc (i would most likely go with thermo fans anyway). But they dont open until the 12th of january so i cant ask them

---

What's your capability?

Fitting is easy, with a marks plate and engine mounts, you'll need a set of block huggers and a new exhaust, Retaining the VC fan is quite possible, just have to set the shroud up CORRECTLY

The Holden 5l is relatively easy, reliable and a good upgrade in comparison to a rover V8

Ask some questions and I'll see if I can help, I can run you through all this stuff by phone if you like, but not till tomorrow, My heads no good, after boozing on with the old man last night,

Quote:

---

Originally Posted by rovercare

What's your capability?

Fitting is easy, with a marks plate and engine mounts, you'll need a set of block huggers and a new exhaust, Retaining the VC fan is quite possible, just have to set the shroud up CORRECTLY

The Holden 5l is relatively easy, reliable and a good upgrade in comparison to a rover V8

Ask some questions and I'll see if I can help, I can run you through all this stuff by phone if you like, but not till tomorrow, My heads no good, after boozing on with the old man last night,

---

:D:DWas that AFTER or BEFORE the tractor fell on its side:p:p:p

BTW, 1:1 TF is a beauty, find myself speeding ALL the time now:(

Regards,

JC

Quote:

---

Originally Posted by rovercare

What's your capability?

Fitting is easy, with a marks plate and engine mounts, you'll need a set of block huggers and a new exhaust, Retaining the VC fan is quite possible, just have to set the shroud up CORRECTLY

The Holden 5l is relatively easy, reliable and a good upgrade in comparison to a rover V8

Ask some questions and I'll see if I can help, I can run you through all this stuff by phone if you like, but not till tomorrow, My heads no good, after boozing on with the old man last night,

---

my mechanical capability is fine im not worried about that side of things at all. The electrical scares me a bit but i have people to help. I have a welder and stuff if i need to fabricate new brackets for things.

I was thinking the same thing as you Rovercare, the 5.0L is a reliable donk and over time will cost less to maintain and repair, plus on gas the running costs would be the same if not better then the diesel in terms of fuel. PM me your number and a good time to ring and i will give you a call. matt

oops double post, why does it say you cant post so soon and need to wait 30secs but then post anyway?

A few of questions Rovercare, getting the engine in as i said isnt what bothers me, as you said with the adaptor plate from Marks it shouldnt be to hard, and they make the engine mounts etc to suit aswell.

Questions;

1) If they dont make the plate to fit to a diesel bell housing can i just bolt a rover V8 one to my gearbox to get around it or does that affect the clutch set up and all.

2) According to their site i can use a holden clutch and pressure plate with the holden flywheel as the spline is the same. But will the holden clutch be up to the task?

3) According to the Marks Adaptors site you need a few different things to get around the security measures fitted to the motor and the car when it was in the holden, have a look at the link i posted earlier and read what they say, this is the stuff that confuses me, the parts they are selling seem expensive and i dont understand enough about electronics to be able to know if i need it or if they are telling me i do.

4) The mention stuff about the engine requiring a small surge tank to draw from to avoid fuel starvation issues when going up steep hills etc, is this necessary.

5) I take it my diesel fuel tank will need to go, what will i put in in its place. Could i look at a LRA long range tank or something instead?

I would have thought that if you ran a tank that had the EFI pump in it that you wouldn't need to run a swirl pot.

The way they are talking about is using a regular tank that pumps fuel with a normal lift pump to fill the swirl pot and then the high pressure EFI pump from there to the engine. $120 for the swirl pot, $70 for the EFI pump and $40 for the lift pump + return hosing between the motor/pot and pot/fuel tank. Its also a common setup and would probably allow you to maintain your current fuel tank.


If the holden clutch is off that motor there shouldn't be any reason why it wont cope.

Quote:

---

Originally Posted by Slunnie

I would have thought that if you ran a tank that had the EFI pump in it that you wouldn't need to run a swirl pot.

The way they are talking about is using a regular tank that pumps fuel with a normal lift pump to fill the swirl pot and then the high pressure EFI pump from there to the engine. $120 for the swirl pot, $70 for the EFI pump and $40 for the lift pump + return hosing between the motor/pot and pot/fuel tank. Its also a common setup and would probably allow you to maintain your current fuel tank.


If the holden clutch is off that motor there shouldn't be any reason why it wont cope.

---

I would like to retain the current fuel tank if i could. Marks do a swirl pot/surge tank kit with all the gear including pump etc etc. Cant remember how much it was, a bit more costly than all of what you listed added together slunnie.

Quote:

---

Originally Posted by justinc

[/b]

:D:DWas that AFTER or BEFORE the tractor fell on its side:p:p:p

BTW, 1:1 TF is a beauty, find myself speeding ALL the time now:(

Regards,

JC

---

Haha, after, I grabbed my camera and all and only remembbered after we got it back on its wheels:mad:, Its only a widdle twactor:D



Hoon!:p

Ace, I'll get to your answers later, when I'm not stopped on the side of the road in bumfug:D

I can't answer the box one, as I've never done a conversion ex-tdi, sorry:(

Quote:

---

Originally Posted by rovercare

Ace, I'll get to your answers later, when I'm not stopped on the side of the road in bumfug:D

I can't answer the box one, as I've never done a conversion ex-tdi, sorry:(

---

No worries.