Isuzu engine mounts

https://www.aulro.com/afvb/

On the left LR (new) engine mount - right is still good (used) truck mount
The rubber only is (LxWxH) 67 mm (77 mm at the mid-point) x 62 mm x 40 mm while the truck is 60 mm x 52 mm x 35 mm. The steel base of the
mount on the LR type is 3.2 mm thick while the truck is 4.5 mm.

http://img412.imageshack.us/img412/2...uzu4bd1052.jpg
LR mount on the left.

http://img697.imageshack.us/img697/4...uzu4bd1065.jpg
Here it's on the right.

Rob W

they are interchangeable, the differnce is the isuze version of the mount doesnt come with the rubber sleeve over the top of the RH side one.

The military 110 parts book has the mounts listed with both a Landrover number and an Isuzu part number, this is what I got from Don Kyatts. It looks the same as the one Isuzubob show in his photos as the LR mount.

Quote:

---

Originally Posted by isuzubob

http://img198.imageshack.us/img198/456/isuzu4bd1044.jpg

On the left LR (new) engine mount - right is still good (used) truck mount
The rubber only is (LxWxH) 67 mm (77 mm at the mid-point) x 62 mm x 40 mm while the truck is 60 mm x 52 mm x 35 mm. The steel base of the
mount on the LR type is 3.2 mm thick while the truck is 4.5 mm.

Rob W

---

Thanks Bob,

So if you used the Isuzu truck mount, you'd have to space it about 9mm off the chassis on both sides as it's not as thick overall (62+3.2) - (52+4.5) = 8.7mm difference in overall thickness?

Quote:

---

Originally Posted by County3.9

The military 110 parts book has the mounts listed with both a Landrover number and an Isuzu part number, this is what I got from Don Kyatts. It looks the same as the one Isuzubob show in his photos as the LR mount.

---

So it sounds like there is more than one mount available from Isuzu - that's good news! Do you still have the Isuzu part numbers for the LR looking items?

Jon

Quote:

---

Originally Posted by D3Jon

Do you still have the Isuzu part numbers for the LR looking items?

---

watching....

Quote:

---

Originally Posted by Blknight.aus

they are interchangeable, the differnce is the isuze version of the mount doesnt come with the rubber sleeve over the top of the RH side one.

---

The rubber cover, which I assume is to protect the rubber mount from spilt fuel from the feed pump strainer is available as a separate part.
# 9532196020

http://img194.imageshack.us/img194/3...4bd1001.th.jpg

Overall height of the LR mount is 49 mm compared to truck 45 mm.

Looking at the sales docket I also found a number that Don Kyatt uses, included below...

LH Eng mount
Isuzu part no: 5532150320
Don Kyatt no: 2Y3112

RH Eng mount
Isuzu part no: 5532150310
Don Kyatt no: 2Y3111

So

Can a change in engine mounts improve the shaaaaake factor :cool:

Quote:

---

Originally Posted by land864

So

Can a change in engine mounts improve the shaaaaake factor :cool:

---

I like my daily massage as I drive to work:p

I'll swap 'smooth' for 'reliable and bullet proof' any day!

Quote:

---

Originally Posted by land864

So

Can a change in engine mounts improve the shaaaaake factor :cool:

---

I run industrial anti-vibration mounts in mine. 3" round and 1.5" thick with m10 studs on each side. Pretty soft.
Either I don't have the shaking problems that bug you guys or I'm soo insensitive I don't care.:angel: The engine rocks around about 20mm at idle on these mounts.