Page 7 of 7 FirstFirst ... 567
Results 61 to 70 of 70

Thread: Fabricated 4WD Diffs based on the Ford 9"

  1. #61
    Join Date
    Jan 1970
    Location
    Gold Coast, QLD
    Posts
    3,566
    Total Downloaded
    0
    Looking at possibly nissan third with dana 60 outers.
    3.7 gears and custom rcv or longfield cv axles. Just not sure on the steering side of things and whether the hybrid diff housing could be made with enough clearance using a h233 or h260 third.... this is way harder then I expected lol!
    I rule!!!

    2.4" of Pure FURY!!!

  2. #62
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    13,671
    Total Downloaded
    0
    There was somebody doing LC80/100 front axles with Patrol front centre?

    Short of that or LC/Lux centres into your housings I'm guessing you'll be putting a lot of coin down.
    Cheers
    Slunnie


    ~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~

  3. #63
    Join Date
    Jan 1970
    Location
    Gold Coast, QLD
    Posts
    3,566
    Total Downloaded
    0
    Quote Originally Posted by Slunnie View Post
    There was somebody doing LC80/100 front axles with Patrol front centre?

    Short of that or LC/Lux centres into your housings I'm guessing you'll be putting a lot of coin down.
    I am of the opinion that the toy conversion is not going to gain me anything over the current arrangement.

    I want to step it up a notch and yes I feel the coin side of this is going to hurt!
    I rule!!!

    2.4" of Pure FURY!!!

  4. #64
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    13,671
    Total Downloaded
    0
    Quote Originally Posted by Grimace View Post
    I am of the opinion that the toy conversion is not going to gain me anything over the current arrangement.

    I want to step it up a notch and yes I feel the coin side of this is going to hurt!
    You talking 9's in fabricated housings?
    Cheers
    Slunnie


    ~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~

  5. #65
    Join Date
    Jan 1970
    Location
    Gold Coast, QLD
    Posts
    3,566
    Total Downloaded
    0
    Quote Originally Posted by Slunnie View Post
    You talking 9's in fabricated housings?
    9 or Nissan not entirely sure what to do! I feel the H260 nissan third will be too large so may have to work with a hi9
    I rule!!!

    2.4" of Pure FURY!!!

  6. #66
    Join Date
    May 2009
    Posts
    3,394
    Total Downloaded
    0
    Quote Originally Posted by Grimace View Post
    9 or Nissan not entirely sure what to do! I feel the H260 nissan third will be too large so may have to work with a hi9
    Uny luck with this?

  7. #67
    Join Date
    Jan 1970
    Location
    Gold Coast, QLD
    Posts
    3,566
    Total Downloaded
    0
    Quote Originally Posted by blackrangie View Post
    Uny luck with this?
    Nope, everything was practically double my anticipated budget.

    Which is mainly my fault for being such a poor tight....
    I rule!!!

    2.4" of Pure FURY!!!

  8. #68
    Join Date
    May 2009
    Posts
    3,394
    Total Downloaded
    0
    Quote Originally Posted by Grimace View Post
    Nope, everything was practically double my anticipated budget.

    Which is mainly my fault for being such a poor tight....
    Yeah tuff gear is not cheap..but then again breaking good gear is expensive

  9. #69
    Join Date
    Sep 2014
    Location
    Melbourne
    Posts
    18
    Total Downloaded
    0

    Toy Hybrib diff

    I'm running lux rear center (beefed up and locker), custom axle and flange. Front is a beefed up 100 serrries beefed up, custom axles with long field cv and locker with 35" Simeon. 350 vortex chev 245kw and 550nm. I drive it pretty hard and it's bullet proof. My setup would run 40's all day long. Rover housings retain ground clearance its win win. In saying that a full Ashcroft setup is still pretty strong

  10. #70
    Join Date
    Dec 2014
    Location
    FNQ
    Posts
    1,016
    Total Downloaded
    0
    Quote Originally Posted by Nuttbag007 View Post
    I'm running lux rear center (beefed up and locker), custom axle and flange. Front is a beefed up 100 serrries beefed up, custom axles with long field cv and locker with 35" Simeon. 350 vortex chev 245kw and 550nm. I drive it pretty hard and it's bullet proof. My setup would run 40's all day long. Rover housings retain ground clearance its win win. In saying that a full Ashcroft setup is still pretty strong
    Have you got pics of this or some more details?
    Who did your axles & hubs?
    Roads?.. Where we're going, we don't need roads...

Page 7 of 7 FirstFirst ... 567

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!