Results 1 to 6 of 6

Thread: LLAMS for L663 Defender

  1. #1
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    10,526

    LLAMS for L663 Defender

    LLAMS kits are now available for the L663 Defender. The kits differ from the L405/L494 kits in that the switch lead is substantially longer and an extension lead is supplied to fit between the LLAMS loom and the LLAMS module to allow the module to be located in a more accessible spot than next to the suspension module. The module will be supplied with HIGH pre-calibrated at +60mm but can be OR2 height as a calibration option and an alternate LOW calibration is also available as a calibration option. These options are identical to those available for the L405 RR and L462 Discovery (D5). The RRP is $605, being $11 more than the RRP of the other similar kits due to the additional cost of the module extension lead. Davis Performance Landys will have 2 kits in a couple of days.

    Note that while the module extension lead may appear to be a VGA/SVGA cable, a VGA/SVGA cable must not be used. The supplied cable has all 15 wires connected 1:1 without any cross-over or common wires.
    MY12 RRV 4.4 TDV8 AB, +LLAMS, +e-diff, +ACC stop/go. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi

  2. #2
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    14,217
    Great work Graeme.
    MY08 TDV6 SE D3- permagrin ooh yeah !
    98 TDI AUTO SE DISCO - gone and will be missed.
    2003 Dingo offroad camper trailer
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan

  3. #3
    Join Date
    Jul 2021
    Location
    Sydney
    Posts
    2

    Llams new installation causing air suspension fault

    Hi Graem.

    Iím writing here as it was your most recent thread.

    I have installed the llams today on my disco2016 and all went well used it once and then car got stuck on top height with a suspension fault and I canít get it to work since.

    Tried disconnecting the unit back to normal but still no luck.

    Tried disconnecting the battery over and over to try reset error but with no luck.

    Would love to hear your guidance as what I can do with getting it fixed.

  4. #4
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    10,526
    I'll send you a PM. You could email me at kits@llams.com.au

    Perhaps just a plug isn't properly fitted.
    MY12 RRV 4.4 TDV8 AB, +LLAMS, +e-diff, +ACC stop/go. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi

  5. #5
    Join Date
    May 2021
    Location
    Perth
    Posts
    18

  6. #6
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    10,526
    He's remembering his previous L320 RRS then D4 Llams medium height which was 30mm but for the Defender, D5, L494 RRS and L405 RR medium raised is OR1 height, being 40mm except for the L494 which is 35mm. He's a great advocate!
    MY12 RRV 4.4 TDV8 AB, +LLAMS, +e-diff, +ACC stop/go. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!