Page 1 of 2 12 LastLast
Results 1 to 10 of 15

Thread: Blue/Grey smoke from 200tdi defender

  1. #1
    Join Date
    Jan 2010
    Location
    Mt Nasura
    Posts
    142
    Total Downloaded
    0

    Blue/Grey smoke from 200tdi defender

    So I'm hoping that some of you wise people might be able to suggest appropriate areas to start looking at why Nigel has started smoking blue/grey smoke on cold startup.

    She's not using oil, not loosing coolant, no obvious signs of gasket issue and only smokes long enough to be embarrassing on cold start-up. Tis morning I let her warm up at idle for 15minutes to 'operating' temp for the smoke to go away only after driving off.
    She's not lost any power and there isn't anything else out of the ordinary.

    Any suggestions on what to look for/at/do would be much appreciated.

    Regards

    Martin

  2. #2
    Join Date
    Jan 1970
    Location
    Sussex Inlet. N.S.W.
    Posts
    6,908
    Total Downloaded
    0
    How are the valve stem seals. Wouldn't take much oil to smoke. Jim
    Jim VK2MAD
    -------------------------
    '17 Isuzu D-Max

  3. #3
    Join Date
    Jul 2006
    Location
    Tumbi Umbi, Central Coast, NSW
    Posts
    5,768
    Total Downloaded
    0
    I think grey smoke means it hasn't decided yet who the next Pope should be.

    OTOH, it does sound a bit like valve stem seals.

    1973 Series III LWB 1983 - 2006
    1998 300 Tdi Defender Trayback 2006 - often fitted with a Trayon slide-on camper.

  4. #4
    Join Date
    Aug 2007
    Location
    Loganlea Qld
    Posts
    1,652
    Total Downloaded
    0
    As a general rule with diesels, blue smoke is oil; whilst white/grey smoke often signifies a lack of air, the greyish/white colour of the smoke is usually un-burnt vaporised diesel. Get someone else to start it and stand near the exhaust and have a sniff!
    Check that any of your air inlet pipes/tubes have not collapsed inside. A lot of air intake pipes are laminated and sometimes the inner lamination can break away.
    Regards
    Glen

    1962 P5 3 Ltr Coupe (Gwennie)
    1963 2a gunbuggy 112-722 (Onslow) ex 6 RAR
    1964 2a 88" SWB 113 251 (Daisy) ex JTC

    REMLR 226

  5. #5
    Join Date
    Dec 2009
    Location
    Williamstown, Barossa, SA
    Posts
    3,451
    Total Downloaded
    0
    Hi. I'd be starting with the timing belt, and injectors. If its using no oil then that eliminates most things. Tractor injectors are supposed to be pulled at 1000hrs and tested, not many are, but when we do pull them its surprising how many we find that have a poor spray pattern and or dribble at idle. With an older or higher mileage engine compression will be slightly down, add a cooler morning and the combustion process will be not completed properly. If the timing belt has stretched a little, that will add to the smoke. I'd be surprised if the stem seals are gone, as to make smoke for a while, at least a tea spoon of oil would be needed in each pot each day... It would be using oil, but if they are gone, they can be done with the head in situe... You just have to make sure No 1 piston is at TDC when doing 1 and 4, and at BDC when doing 2 and 3. Just my opinion, Hope this helps. Post a pic of initial cold start up smoke if you like, we can all see....

  6. #6
    Join Date
    Jan 2010
    Location
    Mt Nasura
    Posts
    142
    Total Downloaded
    0
    Well, that's a good start.

    Sitec, the timing belt was replaced less then 12 months ago, so I'm discounting that one. The injectors haven't been looked at in the three years she's been mine, so that'll be something to follow up.

    Glen, the air inlet pipes are also relatively new (~12 months old). Had them replaced when the timing belt was done. I did check them out this morning and they feel fine.

    Vnx205 - very good, I like that one

    Jx2mad - haven't gone that way yet. I'm baffled a bit because the smoke does go away, so my thinking is if the valve stems are dodgy, then wouldn't the smoke be persistent and not go away?

    I'll have a go with the camera tomorrow morning and see if I can't post the clip...

    Thanks all for your thoughts - lets see what happens....

  7. #7
    Join Date
    Dec 2009
    Location
    Williamstown, Barossa, SA
    Posts
    3,451
    Total Downloaded
    0
    No worries, that's what this forum is all about. So many have done it and seen it and tried it, blown it up, lost it dropped it or sold it!!!! If they were not such a pain to get too I'd suggest checking the timing belt marks all line up as they will run happily one tooth out but do smoke when cold... Don't ask me how I know!!

  8. #8
    Join Date
    Jan 1970
    Location
    Sussex Inlet. N.S.W.
    Posts
    6,908
    Total Downloaded
    0
    Sometimes if valve seals are slightly worn then when the engine is stationary a small amount of oil can seep past into combustion chamber. As I said only a very small amount spread over a couple of cylinders would cause smoke on startup but not when warm. I am thinking re the age of the motor with general wear through age. Even slightly worn valve guides could do the same. Jim
    Last edited by jx2mad; 16th March 2013 at 09:55 AM. Reason: spelling
    Jim VK2MAD
    -------------------------
    '17 Isuzu D-Max

  9. #9
    Join Date
    Jan 2013
    Location
    ACT
    Posts
    577
    Total Downloaded
    0
    Quote Originally Posted by jx2mad View Post
    Sometimes if valve seals are slightly worn then when the engine is stationary a small amount of oil can seep past into combustion chamber. As I said only a very small amount spread over a couple of cylinders would cause smoke on startup but not when warm. I am thinking re the age of the motor with general wear through age. Even slightly worn valve guides could do the same. Jim
    I agree with this post as a good place to look. My (recently sold) '97 Nissan Patrol GQ Wagon did the same thing and it was the strong opinion of an Engineer at my work that this was the cause. Just a small amount of seepage which disappeared shortly after start up.

    Didn't get to test his theory though, as the vehicle sold before we tried to rectify it. A full pre-inspection check was performed by a mechanic, on behalf of the purchaser, and when I mentioned it to him he said the same thing was likely the cause.

    I'm not sure how the other local residents will be able to track my movements now they can't see the copious smoke signals I used to produce upon leaving my driveway

    Cheers,
    Nige

  10. #10
    Join Date
    May 2007
    Location
    Byford, WA
    Posts
    1,317
    Total Downloaded
    0
    Hi Old,
    On my 300 tdi when I had a similar issue I found a couple of the heater plugs to be duff, when I fixed the heater plugs I also had the injectors serviced, apparently two weren't sealing properly and allowing a bit of fuel to leak past, more of an issue when cold than hot obviously.
    Because I fixed two things and the problem went away can't say for sure which had the biggest impact.

Page 1 of 2 12 LastLast

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!