Results 1 to 6 of 6

Thread: Anyone have an old sump plug off a puma? (Measurements please!)

  1. #1
    Join Date
    May 2014
    Location
    Tamworth NSW
    Posts
    4,295
    Total Downloaded
    0

    Anyone have an old sump plug off a puma? (Measurements please!)

    Ideally the 2.2 variant.
    These are replaced with each oil change. It has an integral O ring.
    I'm looking to replace with a fumoto oil drain valve, and hoping to get the sump plug thread measurements, and if possible a good pic of the O ring part, and where it mates on the oil pan. The fumoto valve is supplied with a fibre type washer, so need to ensure that it will seal properly.
    -Mitch
    'El Burro' 2012 Defender 90.

  2. #2
    Join Date
    Jun 2007
    Location
    Margaret River
    Posts
    800
    Total Downloaded
    0
    14 by 1.5 mm

    Ive got a Fumoto on RRS 2.7 (same plug as 2.2)because it is protected by a skid pan
    I used a Stahlbus on the 2.2 Puma as the tube allows you to direct the horizontal flow downwards into a tray. The Stahlbus also has a sealing cap as well as a stop valve. Double security and keeps dust out. The Stahlbus is more compact and less likely to get hooked up offroad than the more protruding Fumoto
    Neither have leaked where they seal to the the pan but use a different seal to the "winged" o ring on the standard plug

  3. #3
    alien's Avatar
    alien is offline A Keeper of the TGO Silver Subscriber
    Join Date
    Jun 2009
    Location
    Bacchus Marsh Vic.
    Posts
    3,337
    Total Downloaded
    0
    I don't change my plug on services(prepares to to be flamed down) but always have a good look at the seal.
    I personally wouldn't fit the valve, my concerns are...
    -I do a fair bit of corrugated dirt roads and would think the weight swinging of the drain thread may lead to the sump cracking.
    -I'd be concerned a rock or stick may hit it when driving on tracks.
    -It could fill with dirt/water/mud and not be usable when needed.
    They have thier places such as machines due to tight access but for once or twice a year is it worth it?
    Cheers, Kyle



    The Good Oil.
    When did you last visit?
    http://www.aulro.com/afvb/good-oil/



  4. #4
    Join Date
    Jun 2007
    Location
    Margaret River
    Posts
    800
    Total Downloaded
    0
    I would not fit a Fumoto to a PUMA either. Its too exposed and even with the plastic locking clip accessory could get hooked and broken or the handle could get inadvertently opened On the RRS it is protected by the protective skid pan. I can change the oil without removing the skid pan if I want.

    The Stahlbus on the other hand is very light and compact and addresses all the concerns Alien mentions on a Puma where the drain is exposed. The cap is sealed and keeps dust and water out.
    The beauty is the draining tube directs the oil where you want. The Puma sump drains horizintally and is messy to control

    https://www.youtube.com/watch?v=wNKvqBPfYE0

  5. #5
    Join Date
    May 2014
    Location
    Tamworth NSW
    Posts
    4,295
    Total Downloaded
    0
    Quote Originally Posted by Grappler View Post
    14 by 1.5 mm

    Ive got a Fumoto on RRS 2.7 (same plug as 2.2)because it is protected by a skid pan
    I used a Stahlbus on the 2.2 Puma as the tube allows you to direct the horizontal flow downwards into a tray. The Stahlbus also has a sealing cap as well as a stop valve. Double security and keeps dust out. The Stahlbus is more compact and less likely to get hooked up offroad than the more protruding Fumoto
    Neither have leaked where they seal to the the pan but use a different seal to the "winged" o ring on the standard plug
    Thanks for the measurements.
    The Stahlbus sounds good. Never heard of them before now, but eagerly youtubing to see what they are all about. The enclosed valve cover is a big plus. The fumoto is a little exposed in this department.

    Quote Originally Posted by alien View Post
    I don't change my plug on services(prepares to to be flamed down) but always have a good look at the seal.
    I personally wouldn't fit the valve, my concerns are...
    -I do a fair bit of corrugated dirt roads and would think the weight swinging of the drain thread may lead to the sump cracking.
    -I'd be concerned a rock or stick may hit it when driving on tracks.
    -It could fill with dirt/water/mud and not be usable when needed.
    They have thier places such as machines due to tight access but for once or twice a year is it worth it?
    I've run one for 7 or so years now on my other vehicle. Never had an issue with it, even when running 3.5kg/mm coilover springs (very hard).
    I think the main concern is the dirt and mud getting into the valve actuating workings (it's a ball valve design), I think the risk of sticks and sump cracking would be negligible- a zip tie or some tie wire will prevent the valve from opening when not required (above its already fiddly up and turn method to open), and the weight is not that significant to cause an issue for cracking. If an impact to rip it off were to happen, the sump plug position of the puma would probably mean you'd have bigger issues to attend to.
    I guess if you look at it as a long term investment, the 40 or so bucks for a fumoto valve is cheaper than 4 changes of a sump plug, if one were to factor that into a maintenance schedule. I myself would go this way for convenience only. It literally makes an oil change a 5 minute affair with no mess (oil down the armpits etc).
    -Mitch
    'El Burro' 2012 Defender 90.

  6. #6
    Join Date
    Feb 2007
    Location
    Yass NSW
    Posts
    5,599
    Total Downloaded
    0
    I have a collection of Disco 3 and Falcon six cylinder sump plugs, I don't bother replacing them unless the seal is damaged. I dropped the oil in the Puma at 12000Ks after we got back from Maralinga and just used the old plug again.

    Regards,
    Tote
    Go home, your igloo is on fire....
    2014 Chile Red L494 RRS Autobiography Supercharged
    MY2016 Aintree Green Defender 130 Cab Chassis
    1957 Series 1 107 ute - In pieces
    1974 F250 Highboy - Very rusty project

    Assorted Falcons and Jeeps.....

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!