Its not good anyway with brake bias towards the front wheels in that situation. You don't have Maxidrive difflocks?
 Master
					
					
						Master
					
					
                                        
					
					
						Guys i own a 300tdi defender with 35 inch tyres.
When trying to use foot brake on a steep hill to hold car i struggle to hold the car? Its scary. Trying to get ideas.
I thought initially vaccum either vacuum pump and servo?
Spoke with dad we are thinking perhaps master cylinder or possible calipers not working. Perhaps a specific brake shop can test and tell me?
The car brakes fine around town no hint of issue or down hill.
Off road braking is all good but your usually in gear.
So the issue is when you stop on a hill and hit the clutch and foot brake the foot brake doest hold!. I thought the vaccum pump issue as your on low revs etc its scary. Any ideas guys perhaps testing vacum pump?
Cheers in advance.
Its not good anyway with brake bias towards the front wheels in that situation. You don't have Maxidrive difflocks?
Cheers
Slunnie
~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
What sort of pedal do you have?
Is it spongy and long, hard and long or just rock hard?
That will tell us a lot.
35's will really test a Deefer's brakes, the booster isn't that great and speaking of which are prone to fatigue cracking around the M/C mount.
Anyone that's had one for any length of time has experienced it, a hard but long pedal.
Get someone to watch the booster and M/C while you stomp on the pedal, if it's cracked you'll see it flex and hear the whistle of air.
Do the usual type of checks of the vacuum hoses back to the booster. Could be vac pump, the stock Wabco ones are crap, plungers are prone to failure and they leak. One of the few places aftermarket, eg Bearmach is better;
If I still had my Deefer I was going to try and graft on a twin diaphragm Disco booster, something I'd really look at with 35's
I know a fella that installed a Disco-1 booster to his Defender and he was running 35's as well. A few mods required to the piping to get it to work but I believe he was happy with the results... Not sure if he's been in your position on a steep hill though...
 Wizard
					
					
						Wizard
					
					
                                        
					
					
						It is probably the master.
Disco boosters are nice but they are no reliable and not needed. The stock later Defender brake system should let you lock the brakes any time you want.
Best guess is a vacuum leak, especially the cracked servo as suggested. Probably not seen round town because you rarely need the brakes on hard more than momentarily.
John
JDNSW
1986 110 County 3.9 diesel
1970 2a 109 2.25 petrol
 Wizard
					
					
						Wizard
					
					
                                        
					
					
						With 35's you need to keep wheel bearings on the tighter rather than loose side as pad knock back offroad becomes a problem I originally set up my brakes with SS pistons, ss braided hoses ,new MC,
Slotted and dimpled rotors,reco the vac pump and check the booster.With 32" tyres the brakes were OK but not as good as I wanted and with 35's worse again so ditched the vac system and went with
Ford f350 super duty Hydroboost unit and a .0625" larger than the 110 MC .This gives higher pedal pressure but less throw which the hydro boost handles no worries .
AM
Noel, pad knock back on dirt was always an issue for me with 33's and I'd always run the bearings with pre-load.
A confidence tap to bring the pads back up before any sort of braking was an unconscious action.
Even my 285/75/16 Mickey Thompson MTZ's are hard on wheel bearings and I am often checking them. I have nipped them up just over the standard torque setting and they are now ok (i'm running oil fed bearings as well). Otherwise when the wheel wobbles from loose wheel bearings, it then causes the brake disc to wobble and this pushes the brake pads back into the caliper which gives you a very soft pedal feel and can cause an oh sh... moment.
I have updated the discs up front to cross drilled and grooved. They should be vented as standard. I use genuine Landrover pads and have braided stainless steel brake hoses.
My 1998 300Tdi 130 is pretty heavy at 3T and doing the above has improved braking greatly.
As advised, check brake booster for cracks close to where the master cylinder bolts on and check that your vacuum pump is working properly.
Andrew
1998 Landrover Defender 300Tdi 130 HCPU Expedition
1972 Peugeot 504 Sedan - Daily Driver
| Search AULRO.com ONLY! | Search All the Web! | 
|---|
|  |  | 
Bookmarks