 Master
					
					
						Master
					
					
                                        
					
					
						Hi Folks, I fear this question just shows my ignorance but I have not found a suitable explanation.
is the TD5 a heavy breather or maybe just like any other diesel?
Mine does breathe a bit from that up top hose (I don't use an oil separator) but I feel that my engine uses only minimal oil. So why does it like to breathe out as it does? Where is that vapor flow created?
 Master
					
					
						Master
					
					
                                        
					
					
						I wonder why this is so. If not a fault then it’s a feature. Blow by must be coming from somewhere and there must be a reason for that
The injector seals leak, even in a good in Td5 , so the Oil lost in fumes is replaced by Diesel from leaky seals .
Not unusual for a Td5 Oil level to increase between services due to being diluted by Diesel.
Smell your dipstick .
 Master
					
					
						Master
					
					
                                        
					
					
						Oh dear, diesel in the oil,never heard this and terrible news. I should not have used synthetic oil to stick with the 10k change interval but stuck with my TdI practice of using Castrol RX diesel and changing every 5000 km!?? I'll have a sniff on my dipstick in a minute!
Just keep an eye on the oil level.
i had 3 D2's,not one had oil in fuel issue.
Not only did i have the oil tested by castrol numerous times,as i knew a guy who worked in their testing lab,i also kept an eye on the sump oil level.
One thing he did say,more than once, was this TD5 oil after 15 000Km is in better condition than the oil in his 4.2TD Patrol after 3 000Km
Cheers
Slunnie
~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
 Swaggie
					
					
						Subscriber
					
					
						Swaggie
					
					
						Subscriber 
 
		I don't think that all TD5s get diesel in the oil or a rising oil level. If the injector seals are installed properly they should not leak. IMHO many do not prepare the base of the injector properly. There is a raised ring on the injector tip that is obscured by hard carbon and must be scraped away very carefully with a dental pick or similar for the new seals to seal.
Mine used to leak more than dilute.LOL
Now my oil level goes down a small amount without too many leaks and that is how it should be.
I also don't think that TD5s breather heavily if they are in good condition.
Breathing is caused by combustion gases leaking down via the rings. That is the only way it happens.
My catch can shows about 10-20CC in say 5000K and the inlet manifold is dry inside.
Regards PhilipA
I hope I'm not teaching you to suck eggs here, but do you understand what blow-by actually is?
Basically combustion byproducts/gasses are blowing past the compression rings and entering the sump, which means we have less than ideal ring seal.
All engines do this and it becomes more pronounced with age, being a mix of ring and bore wear.
Oil type, service history, the way the engine is driven, etc all contribute to wear.
Several lifetimes ago I built race engines for a strictly regulated category.
Most everyone used a leakdown figure of 5% as the condemnation limit for a re-ring, in other words, anythng above this % would result in performance loss.
This was a mileage of under 2000 race and practice km using moly faced race rings, plateu honing and the best syn oils available at the time.
The chrome rings used in diesels wear better than moly but take a lot longer to bed in, but still that might give some indication that at 3-400,000km we're going to see a little more 'breathing' than a fresh engine.
| Search AULRO.com ONLY! | Search All the Web! | 
|---|
|  |  | 
Bookmarks