I think on the later P38A, it was located behind the front bumper.
As above, I’ve fitted RedArc gauges to my 2012 Defender 110.
Some of these gauges have the ability to provide external (or internal) ambient air temps and have a water proof/UV stable temp probe on a suitably long cable.
I’m after suggestions as to where to route/locate the temp probe to provide a realistic outside temp, I.e not effected by direct sun vs reading ambient temp. I have a Safari snorkel fitted to my 110, and so thanks in advance for any advice on how/where you’ve routed and located yours, and the benefits/issues.
Best wishes all.
Ken
I think on the later P38A, it was located behind the front bumper.
Ron B.
VK2OTC
2003 L322 Range Rover Vogue 4.4 V8 Auto
2007 Yamaha XJR1300
Previous: 1983, 1986 RRC; 1995, 1996 P38A; 1995 Disco1; 1984 V8 County 110; Series IIA
RIP Bucko - Riding on Forever
There is a real problem where to locate this on any car - one reason I decided not to bother!
To give a realistic reading while parked, it needs to be open to the air, and not in the sun (regardless of where the sun is), not exposed to radiation off the road, and not exposed to engine heat. While driving, much less critical, as high airflow will make radiation heating insignificant. Just needs to be well clear of the road.
And needs to be not likely to catch on sticks etc.
John
JDNSW
1986 110 County 3.9 diesel
1970 2a 109 2.25 petrol
Yes. The early P38A had it in a location (in an air duct) that would get hot and the correct temp wasn't measured until the car had been driving for a while. That was fine in the UK!
Ron B.
VK2OTC
2003 L322 Range Rover Vogue 4.4 V8 Auto
2007 Yamaha XJR1300
Previous: 1983, 1986 RRC; 1995, 1996 P38A; 1995 Disco1; 1984 V8 County 110; Series IIA
RIP Bucko - Riding on Forever
Exactly right and considerations I’ve factored in hence, where do I put it?
In all my tinkering all these years, I’m not aware of ever seeing a temp probe on any vehicle.
They’re well hidden/located on most vehicles. Im thinking of in the door frame or along the Safari snorkel somewhere, but I want it to be hidden for obvious reasons.👍
Originally Posted by JDNSW;[URL="tel:3178557"
Disco2 is between the bumper and radiators as well.
Cheers
Slunnie
~ Discovery II Td5 ~ Discovery 3dr V8 ~ Series IIa 6cyl ute ~ Series II V8 ute ~
 Wizard
					
					
						Wizard
					
					
						What are you using the info for?
Just to satisfy your curiosity when driving, then out of the sun, in the airflow.
Behind the grill, but in front of the radiators, or in the snorkel will give you what the engines getting.
If it's for when camping then get something you can hang in a tree.
Our Subaru must have two, as the OBD II reader can be 5 deg different to the dash display.
Tony
Most are fitted behind the grill so they are only accurate when the vehicle is moving.
If you are also monitoring the air entering the engine,that will be pretty close to ambient most of the time,but only when the vehicle is moving,as at idle it will read higher due to heat in the engine bay heating up airbox,etc.
I monitor both on the vehicle we have and when moving are generally within a degree or two of each other.
 Master
					
					
						Subscriber
					
					
						Master
					
					
						SubscriberEvery vehicle I have worked on, and that is a whole lot, have the ambient sensor attached to the bonnet support bar, behind the grille. If there is no support bar then the back of the grille would be fine.
Cheers
LuckyLes
| Search AULRO.com ONLY! | Search All the Web! | 
|---|
|  |  | 
Bookmarks