Roof bar mounting detail for P38

[zzsteve]

Hi all,

I have a collection of Rhino roof bar legs and was hoping to adapt some to the P38 roof mounting points. Would anyone be able to post an image or sketch of a "real" one so I can see if this is a possibility?

TIA

Steve

[p38arover]

Go to Rhino and look for RLTPRR legs. Download the fitting instructions.

Here, I've done it for you. :)

RLTP Leg Set - #RLTPRR | Rhino-Rack (http://www.rhinorack.com.au/products/roof-rack-parts/legs/rltp-leg-set_rltprr)

http://rhino-rack-vpm.s3.amazonaws.com/Instructions/Parts/Legs/RLTPRR.pdf

Don't expect any reply from Rhino when asking about kits to adapt other RLTP legs one may have. They don't bother replying.

[whisky_mac]

The three bars just have to be level to each other and clear the roof by a bit so anything that fits that discription should do.

[wayneg]

I should be quite easy as I managed to get an old school gutter mount rack to fit the mounts

[rc42]

Note that the P38 has a curved roof so if you go for a three bar set you will need to have a lower height bar in the center or use spacers on the front and rear bars if they are all the same type.

I have three of the Whisbar HD bars on my P38 and had to use a 15mm spacer kit on the front and another on the back, the three are now perfectly level.

[TheTree]

Note that the P38 has a curved roof so if you go for a three bar set you will need to have a lower height bar in the center or use spacers on the front and rear bars if they are all the same type.

I have three of the Whisbar HD bars on my P38 and had to use a 15mm spacer kit on the front and another on the back, the three are now perfectly level.

Are the spacer kits available or did you make them up?

I have the same issue with my WhispBars

Steve

[rc42]

These HD spacer kits have three 5mm spacers for each end of the bar, I didn't buy them from the link below but a Google search will no doubt find somewhere close. Supercheap would also be able to get them for you as they carry the Whisbar range.

https://www.aulro.com/afvb/images/imported/2014/07/28.jpg

Prorack Whispbar Hd Height Spacer, 15Mm - Rays Outdoors (http://www.raysoutdoors.com.au/online-store/products/Prorack-Whispbar-Hd-Height-Spacer-15Mm.aspx?pid=305795&menuFrom=10109#Cross)

[TheTree]

These HD spacer kits have three 5mm spacers for each end of the bar, I didn't buy them from the link below but a Google search will no doubt find somewhere close. Supercheap would also be able to get them for you as they carry the Whisbar range.

Prorack Whispbar Hd Height Spacer, 15Mm - Rays Outdoors (http://www.raysoutdoors.com.au/online-store/products/Prorack-Whispbar-Hd-Height-Spacer-15Mm.aspx?pid=305795&menuFrom=10109#Cross)

Thanks mate :D

[Rage Over]

I take it you've all seen these ones:

https://www.aulro.com/afvb/images/imported/2014/07/22.jpg

https://www.aulro.com/afvb/images/imported/2014/07/23.jpg

[Rage Over]

See here (don't shoot me for cross-linking!):
Roof rack bracket (http://www.rangerovers.net/forum/7-range-rover-mark-ii-p38/64185-roof-rack-bracket.html#post758514)

[p38arover]

Rhino make a spacer kit. I bought one recently.