No 5 parts diagram and part no list

[towe0609]

Is there such a thing as a parts diagram and part no list for a No5?

In particular I'm looking for the parts no's for the inner seal, lock nuts (can you get regular hex lock nuts?), lock washers (ninja star looking things, or equiv for hex lock nuts), gasket for cup.

Can you buy replacement lenses for the tail lights? Unfortunately one of the Glass Lucas lenses is smashed.

[Mick_Marsh]

Have you asked on REMLR?
They may have that info in their archives.

[Carzee]

...we're working toward a number 5 restoration, with info

101-148 - REMLR Wiki (http://www.remlr.com/wiki/index.php'title=101-148)

[towe0609]

Have you asked on REMLR?
They may have that info in their archives.

Not having much luck with REMLR - tried to create an account and never received email confirmation. Sent in a form and have had no reply.

Have had a poke around, and read Carzee's restoration page ... which suggests the lights are going to be hard to replace and doesn't yet contain info on the seal or lock nuts/washers ... so still got fingers crossed for some advice here.

[towe0609]

Thanks to the wiki and REMLR I found the parts scale for the no 5 and relevant excepts re the axle are below. Searching via these part numbers hasn't returned obvious suppliers...

http://www.aulro.com/afvb/attachment.php?attachmentid=102177&stc=1&d=1448091438

http://www.aulro.com/afvb/attachment.php?attachmentid=102178&stc=1&d=1448091438

http://www.aulro.com/afvb/attachment.php?attachmentid=102179&stc=1&d=1448091438

http://www.aulro.com/afvb/attachment.php?attachmentid=102180&stc=1&d=1448091459

[towe0609]

OK, I think I've found the lock nut and washers....if anyone can confirm that would be great.

http://www.skf.com/webpim/0901d19680390ce3/1201%200070-0071%20-%2010000%20wp.svg

KM(L) and HM .. T lock nuts - KM 9 (http://www.skf.com/group/products/bearings-units-housings/bearing-accessories/lock-nuts/lock-washer-clip-plate/kml-lock-nuts/index.html'designation=KM%209&unit=imperialUnit)

http://www.skf.com/webpim/0901d19680390ce4/1201%200072-0073%20-%2010000%20wp.svg

MB(L) lock washers - MB 9 (http://www.skf.com/au/products/bearings-units-housings/bearing-accessories/lock-nuts/lock-washer-clip-plate/mbl-lock-washers/index.html'designation=MB%209&unit=metricUnit)

[LandroverScott]

Not having much luck with REMLR - tried to create an account and never received email confirmation. Sent in a form and have had no reply.

Have had a poke around, and read Carzee's restoration page ... which suggests the lights are going to be hard to replace and doesn't yet contain info on the seal or lock nuts/washers ... so still got fingers crossed for some advice here.

Howdy,

REMLR forum should be automatic replies to the email address you submitted, REMLR inc registration - I updated them yesterday

cheers
Scott

[towe0609]

Still looking for a part number and/or supplier of the Gasket (Part 12) I thought maybe it would be the same as a drive flange gasket for a series land rover (231505), so I bought some, but they are a few mm too small.

Any help appreciated.

[towe0609]

These gaskets can be obtained from

rubber products, rubber distributor, rubber manufacturer, Melbourne, Sydney, Brisbane, Adelaide, Perth, Australia (http://www.completerubber.com.au/)
51 Sparks Avenue, Fairfield, Victoria 3078
Ph: 03 9482 7222

Shown in their gasket listing as

GASKET AXLE GREASE ADE(V)50-36

around $17 per unit + delivery

I think I'll buy myself a decent punch set and a sheet of gasket from supercheap or the like.


Still looking for a part number and/or supplier of the Gasket (Part 12) I thought maybe it would be the same as a drive flange gasket for a series land rover (231505), so I bought some, but they are a few mm too small.

Any help appreciated.

[towe0609]

Just for the sake of documentation in case it benefits someone else, the seal (Part 003 in the diagram) is a RTC3510 or Corteco 19029100B

I wouldn't recommend opening this link unless you really have to as it take ages to load being a 350+ page document. But it does show the exact dimensions of the seal.

"www.corteco.com/fileadmin/user_upload/media/service/2015_Oil_seals_by_design_web_catalogue.pdf"

Article Number: 19029100B
EAN: 3358960368904
Inner Diameter 1: 58.72 mm
Outer Diameter 1: 85.09 mm
Height 1: 7.94 mm
NBR (nitrile butadiene rubber)

[towe0609]

The bushes are a Mackay Rubber product, Part No S19, BJ Bearings were able to order them for me at a cost of $20 each (ouch)

http://www.mackayrubber.com.au/pdf/flex_I_pages/flexible_Bearings.pdf

Back on the lock nuts and washers, just in case it helps anyone, the bearing shop had the lock washers under part no AW09 (thats a zero) which looks like an NTN part at a cost of $3.54 per unit. Looks like the lock nut is part No AN09.

Looks like in Timken the equivalent is N 09 and W 09

Timken Part Number N 09-W 09, Inch Accessories - Locknut and Lockwasher On The Timken Company (http://cad.timken.com/item/ller-bearing-metric-and-inch-accessories-1/inch-assessories-locknut-and-lockwasher/item-87177)

[towe0609]

Looks like the alternative bush listed in the parts scale is a Motherson Elastomer Pty. Ltd (www.motherson.com.au) product, Part No E20822, Pg 35

After removing 50 years of rust, that is the part no stamped onto the bush on my trailer.

http://www.motherson.com.au/UserFiles/File/pdf/Silentbloc-Catalogue.pdf